Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Polystyrene and thermal insulation

Is EPS density enough to assess its quality?

At a glance

Polystyrene density describes the mass of the material per unit volume. It can help when checking a delivery, but it does not replace the lambda value, strength or the product documentation. We explain how to calculate this parameter, why a heavier pack does not always mean a better choice and when a weighing result requires further verification. Density is mass divided by volume. It is given in kilograms per cubic metre. If the boards themselves weigh 4.5 kg and have a total volume of 0.30 m³, the result is 15 kg/m³. This is an example calculation, not a requirement for any given polystyrene. What is needed is the actual mass of the material and a correctly determined volume of the part of the delivery being tested.

White and graphite polystyrene next to a scale on a workshop table

How do you calculate the density of a board?

The packaging and other additions must be subtracted from the pack weight. Also check the number of boards and their dimensions. The nominal volume of a pack is not always the same for all thicknesses. With profiled edges, the method of determining dimensions and quantity of material may require attention. An error in volume will change the result even when the scales work correctly.

What does density say about the properties of EPS?

Within a given technology and product group, density may be associated with mechanical and thermal properties. However, it is not the only factor. The raw material, additives, material structure and production method all matter. It is therefore not possible to assign one lambda value and one CS(10) level to every possible density regardless of the type of board.

Compare white EPS with graphite EPS with particular caution. The additive that changes the thermal properties makes it possible to achieve a different lambda without simply reproducing the relationship known from the white material. Two similarly heavy boards can have a different thermal resistance at the same thickness. Weighing alone also does not show water absorption or compatibility with the façade system.

Why is the label more important than the feel in your hand?

Pressing with a finger gives only a subjective impression of how the surface behaves. It is not a test of CS(10), TR or flexural strength. Nor does the number of visible granules allow lambda to be calculated reliably. What is needed for assessment are the declared properties and suitable test methods. The colloquial term “zbity styropian” does not replace a technical specification.

In floors, the properties relating to load are what matter; in ETICS, among other things, TR; and in foundations, also the water-related parameters. Density can supplement this information if the manufacturer declares it or specifies it in the documentation. However, a missing property should not be replaced by the assumption that a heavier board certainly meets all the necessary requirements.

When is weighing a pack useful?

It can serve as an initial check that the material matches a specific reference. If the manufacturer states a density or a requirement for a given grade, it is worth comparing the measurement with that document. A large discrepancy should prompt clarification. First, however, check the number of boards, the thickness, the condition of the material and the accuracy of the measurement before you consider the delivery defective.

Do not compare packs of different volumes by weight alone. A pack of thicker boards may contain fewer pieces, and the manufacturer may use different pack sizes. Moisture or soiling also affects the weighing result. For a complaint, keep the label and describe the measurement method. Without this data, the number of kilograms is difficult to interpret.

Does low mass mean a material defect?

Not automatically. Lightness is one of the characteristics of EPS, and the appropriate density level depends on the grade and the application. The assessment should refer to the declaration and the project requirements. A board that meets the required parameters does not become unsuitable merely because it weighs less than another product intended for higher loads.

On the other hand, a matching mass does not confirm all properties. The material may be damaged, have incorrect geometry or not correspond to the required application. Delivery verification therefore includes documents, appearance and storage conditions. If there is a specific doubt about a declared characteristic, a test of that characteristic is needed, not another weighing.

How to buy without reducing everything to kilograms?

Establish the parameters needed in the given part of the building and compare offers using the same specification. Enter the thickness, lambda value and required mechanical or water-related properties in the order. If you use density as an additional check, state its basis. This way you avoid a situation in which the seller and the contractor understand the term “good EPS” differently.

Well-known EPS manufacturers include Styropmin, Yetico, Austrotherm and Arbet. Data on density and other properties must be checked for the specific product.

Also compare the cost of achieving the required effect. A heavier board does not always reduce energy consumption, and a lighter one does not always meet the floor requirements. The most useful thing is that the material matches the task. Density remains one piece of supporting information, while the declared properties show how the product behaves in specific tests.

7 branches. Materials closer to your project.

Izoprofil.pl map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote

Materials for your project