Fibre cement coverings
Setting out rows of corrugated sheets: preparing a laying plan
At a glance
A well-planned roof is not created by adding successive sheets up to the ridge. First, you have to determine where the laps, supports and cuts will be. Fibre cement sheets have specified working dimensions and a laying direction. It is worth ordering asbestos-free fibre cement only after checking the entire roof slope. A row plan helps to limit waste, avoid narrow end pieces and prepare the right number of full sheets and sheets prepared in advance. Two roof slopes with the same number of square metres may require a different set of sheets. One is rectangular, the other has a valley flashing, a chimney and a diagonal gable. That is why the dimensions of the edges, the diagonals and the position of all obstacles are needed for the layout planning.

Start with the outline, not with the surface
When renovating, it is worth verifying the actual condition, because an old drawing need not correspond to the building after alterations. The outline should also indicate the support lines and the planned finishes. Only on such a base plan can it be seen whether a given format suits the roof. Buying on the basis of surface area alone can leave a lot of material that is unsuitable for the required cuts.
Use the cover dimensions to calculate the rows
The nominal width and length of the sheet include the parts intended for the overlap. Fibre cement sheets therefore cover a smaller area than results from simply multiplying their external dimensions. The installation values specific to the system and the pitch must be entered into the plan. For example, five rows with a working length of 1.00 m give five metres of repeatable coverage, not the sum of the full sheet lengths. This is an illustrative calculation, without reference to a product. The start at the eaves and the finish below the ridge require separate checking. The same overlap should not be applied mechanically to every non-standard detail.
Assess the first row and the last strip together
It is tempting to start with full sheets at the eaves and postpone the decision about the top until later. However, this can leave a very short piece at the ridge. Fibre cement sheets must have room there for support, holes and proper covering. That is why the entire length arrangement is considered at once. Sometimes a different format or a shift provided for in the design gives a more favourable cutting layout. The overlaps should not be reduced merely to fill the missing section. Pre-formed holes and corners further limit the scope for changes. The plan makes it possible to detect these dependencies before delivery, when correcting the order is still straightforward.
The laying direction determines how the sheets are prepared
The orientation of the side laps and cut corners follows from the instructions. Not all versions can be rotated or laid in any order. Asbestos-free fibre cement with factory finishing should be marked in the plan in accordance with the intended use. It is worth distinguishing between middle, starting and edge sheets. At openings or gables, full elements may be needed, prepared separately. Such a division makes it easier to organise the pallets and to feed the material. It also reduces the risk that a correctly finished sheet is used in the wrong place and then turned round to rescue the lap. An orientation error can carry over to the entire row.
Obstacles must be incorporated into the sheet grid
Chimneys, roof hatches, skylights and service penetrations affect the cutting plan and fixing. Fibre cement sheets should not end in narrow, unsupported strips around such locations. It is necessary to check whether the layout can be shifted in a permissible way and where additional support is needed. A daylighting element has its own documentation, even when it repeats the corrugation of the adjacent covering. It cannot be regarded as a transparent version of the same sheet. The plan should also show the flashings and the direction of water drainage. The opening outline alone, without a solution for its edges, is insufficient for preparing an order.
The reserve results from the cutting layout and the risk of damage
There is no single waste percentage suitable for every roof. A simple slope made of full sheets and a roof with numerous valleys have different requirements. Fibre cement sheets should be calculated according to formats and places of use. A piece cut off from one side cannot always be used on the other. It may have the wrong overlap edge, holes or corner orientation. In addition to the cutting plan, the organisation of delivery and the agreed service stock are taken into account. It is good for this to be described as a specific number and sheet variant. Random offcuts may not be useful for a future replacement of a full sheet after damage.
The plan must be clear for the team on the roof
The best schedule is of no help if the installer cannot relate it to the building. Marked roof slopes, laying direction, row numbers and a list of formats are needed. Fibre cement sheets should be assigned to locations with a separate description of cuts and corner preparation. The plan should also indicate changes at supports and fixing zones. Before starting work, the installer compares it with the measurements. Any discrepancy must be clarified before the first holes are made. After installation, it is good to keep a version reflecting the actual changes. This will make it easier to select parts during repair and avoid having to reconstruct the entire layout from the ground again.
Send a dimensioned roof outline so that asbestos-free fibre cement can be selected according to the actual row plan. The cutting plan allows formats to be compared and the full scope of the order to be calculated.
7 branches. Materials closer to your project.

