Collar beam roofs: structure, costs and limitations

A collar-tie roof is a structure of rafter pairs connected by transverse timber members called collar ties, whose position and connections directly shape how the entire roof truss performs. Before deciding, it is worth establishing whether the design allows the loft to be adapted without removing the collar ties, since this element often limits layout freedom. Check that the collar-tie-to-rafter connections match the solution assumed in the calculations — random screws or extra holes can weaken the timber. The choice of structure is governed by span, loads and how forces are transferred to the walls, not by a sketch alone.

By |2026-11-14T22:27:20+01:002023-06-26|Technology and applications|Comments Off on Collar beam roofs: structure, costs and limitations

Can solar panels be mounted safely on a metal roof?

Photovoltaics can be installed on a metal roof if the structure has adequate load-bearing capacity and the mounts suit the specific covering. The information 'metal roof' alone is not enough to select the fixings. The profile, sheet thickness, supports, wind and snow loads and the method of sealing must be taken into account. It is easiest to agree these matters before the roof is installed. With an existing covering, a prior assessment of its condition is needed. Start with the structural documentation and a roof inspection. The installation adds extra weight and changes how wind and snow act. The entire load path must be assessed: from the module, through the mounts and covering, to the load-bearing elements. Good paint condition on the sheet metal is not proof of sufficient load-bearing capacity of the trusses or purlins.

By |2026-11-14T15:41:10+01:002023-06-07|Technology and applications|Comments Off on Can solar panels be mounted safely on a metal roof?

Sizing trapezoidal steel sheets for a roof or wall

Trapezoidal steel sheet is selected on the basis of where it will be used, the loads and the dimensions of the surface to be covered. The profile designation helps identify its height, but does not describe the entire geometry. To place an order, you need the cover width, the sheet length and the support layout. It is worth starting with the cutting plan before you compare prices alone. In common families, the designations T18 and T35 refer to profiles approximately 18 and 35 mm high. However, the number does not specify the corrugation pitch, the cover width or the steel thickness. Two sheets with the same abbreviated name may differ in cross-section. Therefore compare the drawing, not just the figure in the price list.

By |2026-11-14T15:39:18+01:002023-06-04|Technology and applications|Comments Off on Sizing trapezoidal steel sheets for a roof or wall

What do T18 and T35 mean on trapezoidal steel sheets?

T18 and T35 indicate the trapezoidal profile family, usually linked to the rib height. They do not describe all the parameters of the sheet. To compare products you need the cross-section drawing, steel thickness, cover width, coating and intended use. Two products with a similar designation may have a different geometry. That is why ordering just a "T18 sheet" is too imprecise, especially when matching an existing roof. The letter T is commonly used to designate trapezoidal steel sheets. The number indicates the profile height family, but the exact dimension should be read from the product data sheet. Additional letters may also appear. Their meaning follows from the designations used by the given manufacturer. There is no basis for interpreting any symbol added to T35 in the same way for every supplier.

By |2026-11-14T15:41:49+01:002023-05-29|Technology and applications|Comments Off on What do T18 and T35 mean on trapezoidal steel sheets?

How tile-effect metal roofing coatings differ and what they protect

Choosing a metal roofing tile depends not only on colour but above all on whether the coating system suits the conditions around the house. The coating protects the steel core and gives the finish its appearance, so when comparing offers check the product data sheet: the type of organic layer, the declared resistance and the intended environment. Remember that coating thickness given in micrometres is not the same as the thickness of the steel core in millimetres. Even a good product will not guarantee durability if swarf or scratches are left behind during transport and installation.

By |2026-11-14T18:55:54+01:002023-05-14|Technology and applications|Comments Off on How tile-effect metal roofing coatings differ and what they protect

How much does it cost to install panels with many openings, corners and short sections?

Two walls with the same surface area may require different amounts of labour. Edges, openings and the number of cuts also determine the installation price. With small areas, the share of flashings and seals increases. A quote should therefore be based on the cladding drawing and the access conditions at each installation location. A large, regular area allows the same panel laying method to be repeated. With many short sections, lengths are changed more often and terminations are prepared. Work at corners is added to this. The number of installed metres does not directly reflect the number of operations performed.

By |2026-11-14T12:01:45+01:002023-05-07|Technology and applications|Comments Off on How much does it cost to install panels with many openings, corners and short sections?

Modular tile-effect metal roofing: uses, benefits and installation

Modular metal roofing is a system of repeatable panels joined on the roof slope, useful where handling ease and a well-planned layout matter. Before buying, however, check not only the covering area and minimum pitch but also the coating and the complete set of accessories. The quality of the roof depends on the whole system, not on the sheet size alone. A key variable is how the module matches the roof geometry – this determines waste and cutting options. The panel format is fixed for a specific product, so the name alone does not identify the parts.

By |2026-11-14T18:54:17+01:002023-05-04|Technology and applications|Comments Off on Modular tile-effect metal roofing: uses, benefits and installation

Will 40 mm second-quality insulated roof panels suit your roof?

For a 40 mm second-grade roof panel, first check the intended use, the condition of the joints and the usable lengths. A thin core does not mean that any support spacing is acceptable. A reduced price does not remove the requirements for slope and tightness. Buying makes sense when the specific components suit the project and the extent of their defects is known. In roof panels, the nominal core thickness and the overall height may differ. The upper steel sheet has a profile that increases the external dimension of the component. Check the cross-section of the actual panel. Measuring at the top of the trapezoidal profile without knowing the designation can lead to an incorrect comparison of two offers.

By |2026-11-14T15:38:37+01:002023-05-03|Technology and applications|Comments Off on Will 40 mm second-quality insulated roof panels suit your roof?

Planning lengths and corners for made-to-measure parapet copings

With a parapet, the building perimeter is not the only thing that matters. Copings must fit the actual wall width, the position of the layers and the planned drainage. The order must include straight sections, corners and changes in height. A complete set prepared in this way is easier to install and to accept. It also avoids a situation where the straight strips are ready but one end piece is missing, stopping the whole parapet from being closed. Measurement should cover all layers that will sit under the flashing. The dimension of the wall or structure alone is not enough. The final finish on both sides must be taken into account. If the façade is not yet finished, its actual thickness needs to be agreed.

By |2026-11-15T02:37:02+01:002023-04-24|Technology and applications|Comments Off on Planning lengths and corners for made-to-measure parapet copings

How to prepare a metal roof for repainting

Painting a metal roof makes sense only when the steel and its fixings can accept a new coating. First establish whether surface deposits, faded paint or perforation of the sheet rule out renovation. The key decision is matching the system to the existing finish and its adhesion, in line with the supplier's documentation. Also check the gutters, eaves, areas around the chimney and service penetrations, plus the underside of the covering where accessible. The scope of repairs and substrate preparation should follow this assessment, not the desired colour.

By |2026-11-14T18:55:13+01:002023-04-21|Technology and applications|Comments Off on How to prepare a metal roof for repainting
Back to top