Technology and applications2026-11-15T17:17:10+01:00

Choose a product group

Metal roofing

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Technology and applications

Izoprofil.pl explores how building materials work together. Sandwich panels, PIR insulation and trapezoidal sheets depend on their supports, joints, fixings and drainage. The guides explain how product properties affect use on roofs, walls and insulation assemblies. They help you read the documentation, identify limits and prepare questions for your designer or contractor. You can also look up detailing, common faults and preparing materials for installation. Use the technical issue on your project to choose an article, then check the instructions for your specific product. Similar-looking components may have different requirements.

How do you convert EPS to PIR without confusing thickness with thermal performance?

A centimetre of EPS does not provide the same thermal resistance as a centimetre of any PIR board. The comparison must be based on the lambda value of the specific material. The whole wall build-up and its finish are then checked. A thinner layer may make the reveal detail easier to resolve, but the difference in thickness alone does not determine the choice. First read the lambda value of both products under consideration. Do not assume a single figure for all EPS or for the entire PIR group. Properties depend on the variant. A board with a metallised facing may have a different application and parameter from a board intended for plaster.

Renovating a flat roof with Eurothane Silver: when details need changing

Insulating a flat roof may require raising the flashings and adjusting the position of the outlets. Eurothane Silver should be selected after these constraints have been assessed. First, it must also be checked whether the old layers are dry and whether they can serve as a substrate for the new build-up. Recticel Eurothane Silver is a PIR board with multi-layer gas-tight foil on both sides and a printed grid. The current data sheet specifies it for flat roofs in a classic build-up. During the pre-renovation inspection, examine the classic flat roof for which mechanical fixing, bonding or ballasting is being considered. Eurothane Silver must be assigned to a specific mechanically fixed, bonded or ballasted system before the scope of demolition is determined and the old roof construction is prepared.

Choosing one supplier for sandwich panels and sheet metal

A large selection of material only helps if you can assemble your own building from it. With panels and sheets, matching dimensions, accessories and efficient delivery are important. The size of the warehouse does not answer all these questions. A supplier is worth assessing against a specific schedule, not just the number of offers. Start by dividing into walls, roof and flashings. For each group, enter the dimensions and required properties. For panels, the core, thickness and module are needed. For sheets, also the profile, steel thickness and cover width. Colour without the type of coating does not complete the material description.

Fibre cement roof ridge. Selection of fittings and ventilation

The ridge looks like a narrow strip at the top of the roof, but it combines several important functions. It covers the junction between the roof slopes, takes up water driven in by the wind and can provide an outlet for air from beneath the covering. Fibre cement sheets require a compatible set of fittings and fastenings here. Asbestos-free fibre cement does not form a complete roof without the correct termination. Choosing a ridge tile by colour alone overlooks the factors that determine tightness and moisture beneath the covering. The type of ridge element depends on the roof pitch and the way the two sides are joined. Some solutions have a defined adjustment range, others require the correct angle. This range is not, however, the permissible pitch of the covering itself.

Floor renovation: when Kingspan Therma TF70 can help

In a renovated floor, Therma TF70 must reconcile thermal requirements with the existing levels at doors and stairs. Equally important is the support of the boards over old chases. An inspection before laying the insulation can therefore change both the cross-section and the scope of substrate preparation. Kingspan Therma TF70 is a PIR board for insulating heated and unheated floors. It has a multilayer facing containing aluminium on both sides. The floor level must be agreed with the space for TF70, the screed and the final finish before determining the scope of demolition and preparing the old building element.

Replacing the roof covering with Powerroof: retaining the finished loft interior

A finished attic is a strong argument for carrying out part of the work from the outside. Powerroof can make this type of thermal insulation possible, but not always without changes to details. Before renovation, access, weather, the condition of the timber and the possibility of closing the roof tightly must be checked. Recticel Powerroof is a PIR board for above-rafter thermal insulation of pitched roofs. It has an aluminium facing and a tongue-and-groove joint on all four edges. During the pre-renovation inspection, check the above-rafter Powerroof layer running over the timber structure of the pitched roof slope. Powerroof must be run over the rafters while ensuring proper fixing of the entire covering before determining the scope of demolition and preparing the old building envelope. The new surface does not solve everything: continuous insulation does not replace the elements that transfer forces from the covering to the structure.

Back to top