Technology and applications2026-11-15T17:17:10+01:00

Choose a product group

Metal roofing

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Technology and applications

Izoprofil.pl explores how building materials work together. Sandwich panels, PIR insulation and trapezoidal sheets depend on their supports, joints, fixings and drainage. The guides explain how product properties affect use on roofs, walls and insulation assemblies. They help you read the documentation, identify limits and prepare questions for your designer or contractor. You can also look up detailing, common faults and preparing materials for installation. Use the technical issue on your project to choose an article, then check the instructions for your specific product. Similar-looking components may have different requirements.

What is a 60 mm mineral wool wall panel sufficient for, and what about the 40 mm variant?

The 60 mm mineral wool wall panel is available in selected systems but is not a universal solution for every building envelope. Its small thickness has thermal and structural implications. The 40 mm panel offer requires separate verification. It must not be assumed that it has the same core and properties as a thicker product of similar appearance. The value refers to the specific panel dimension stated in its documentation. It is necessary to check how the manufacturer describes the thickness and profiling of the facings. An arbitrary point at the joint should not be measured and used as a basis for comparing different products.

What determines batten spacing for T18 and T35 roof sheets?

The spacing of battens under T18 or T35 sheeting depends primarily on the load-bearing capacity of the specific sheet within the adopted support arrangement, not on a single universal rule. To determine it, you need the profile, steel thickness and grade, the loads and the support layout. It is also worth checking the bearing width and the method of fixing the battens. A deeper trapezoidal profile may offer different possibilities, but it does not justify arbitrarily thinning out the substructure. The starting point is structural selection and measurement of the roof slope, not cutting timber alone.

Plastic or metal soffits: how to compare the materials

When comparing PVC and metal soffits, first check whether the eaves allow air to dry the roof. Both materials require profiles and installation clearances, and plastic changes dimensions with temperature. Before installation, inspect the timber, the junction with the façade and how the underlay is led out, as later access will be harder. In the estimate, separate panel area from the length of edge components to compare offers without omitting details. Remember that a soffit does not replace proper metal flashing.

Planning a steel building with an overhead travelling crane

An overhead crane changes how production is handled, but also the requirements placed on a steel hall. Its load capacity matters, but it is not enough to design the supports. The equipment moves, brakes and transfers forces through its wheels onto the track. Span, working height and mode of operation all count. These data must be established before the final choice of structure, not after the frame has been erected. The type of loads carried, their mass and the required reach must be specified. Operating frequency and transport routes are also significant. A steel hall may handle single lifts or an intensive technological process. Such applications are not equivalent. The equipment requirements should follow from the actual mode of use.

Planning a roof replacement step by step

Plan a roof replacement by inspecting the structure first, not by ordering the covering. Check the roof truss from outside and from the attic, looking for leaks, deformation and damaged timber; also assess supports, connections and chimneys. New lightweight sheet metal will not strengthen a weakened truss, and the designer determines its suitability and any necessary reinforcement. Only then establish the scope of formalities, choose the covering and insulation, and plan demolition, acceptance of hidden layers and protection of the house. Leave room in the schedule for repairs revealed after the old material is removed.

IKO enertherm ALU for additional insulation: moisture in the old build-up

When the existing insulation was exposed, a damp section was found. Before adding IKO enertherm ALU, it is necessary to establish where the moisture comes from and which layers can be retained. Replacing the board variant alone does not eliminate leaks or correct the faulty performance of the cross-section. The scope of the repair should follow from the identified cause and the actual condition of the materials. In a renovation, the scope described as renovation of the thermal insulation in a multi-layer building element requires the old layers to be investigated. The first difficult place to inspect is the junction between the new ALU and the section that was damp before the renovation. It is not worth determining the thickness of IKO enertherm ALU solely on the basis of an old drawing. The measurement should cover the extent of the moisture as well as the thicknesses and condition of the layers in the exposed section, taking into account changes made during earlier work.

Back to top