About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Estimating the cost of a panel-clad building from foundations to fit-out

The price of a panel hall depends primarily on the scope of construction. The panels themselves are only one part. Foundations, structure, joinery and services must be considered separately. The proportions and height of the building also have an influence. A reliable cost estimate starts with a single drawing and a clear boundary between the envelope and the complete building. Determine whether the scope covers only the frame and envelope, or also the floor, services and finishing. The term “turnkey” without a list of works remains imprecise. The gate, drainage or power supply may be billed separately. All such items should be included in the schedule.

By |2026-11-14T12:01:09+01:002024-03-16|Technology and applications|Comments Off on Estimating the cost of a panel-clad building from foundations to fit-out

Choosing a practical roofing course

Good roofing training should let you carry out and check important details yourself. A display of a finished roof is not enough. Before signing up, establish which system the course covers, how much time is set aside for practical work and whether mistakes are discussed. Exercises linked to the current instructions, real material and safe working conditions provide the greatest value. First determine what you want to learn. Installing modular tile-effect metal roofing requires different exercises than building a hall cladding from insulated sandwich panels. The details of low trapezoidal steel sheet and high structural sheet also differ. General training can organise the basics, but it does not replace learning the seams, fasteners and installation sequence of a specific system.

By |2026-11-14T15:40:21+01:002024-03-14|Technology and applications|Comments Off on Choosing a practical roofing course

Choosing a covering for a pitched gable roof

Choosing a covering for a gable roof starts with measuring both slopes. Even when they look symmetrical from the street, their dimensions, exposure to sunlight and roof openings may differ. Check the pitch and condition of the supporting structure before choosing the sheet format. A regular layout can reduce offcuts, provided the sheets suit the measured roof. For a meaningful comparison, ask for estimates that also cover the ridge, eaves and verges. The price per metre of sheet alone gives an incomplete picture of the finished roof.

By |2026-11-14T18:53:55+01:002024-03-14|Technology and applications|Comments Off on Choosing a covering for a pitched gable roof

Metal fence picket profiles: stiffness, ribs and supports

A metal picket is not simply a flat strip of painted steel. Its three-dimensional cross-section helps achieve useful stiffness with a small sheet thickness. That is why two elements of similar width can behave differently. When assessing metal pickets, the profile, length and method of support must be considered together. The appearance of strong pressings alone is not yet proof of load-bearing capacity. A good comparison starts with the drawing and installation conditions of the specific product. Profiling moves part of the material away from one flat surface. Ribs, steps and folded edges are formed. This shape influences the element's resistance to deformation. This is the fundamental reason why sheet steel pickets are not made exclusively as flat strips. The geometry serves a functional purpose, although at the same time it gives the fence its characteristic appearance.

By |2026-11-15T17:18:20+01:002024-03-11|Technology and applications|Comments Off on Metal fence picket profiles: stiffness, ribs and supports

What to check on a metal roof after winter

Start a post-winter roof inspection by following the route rainwater takes. From the ground, look for gutters that sag and flashings that have moved. From the loft, check for damp patches. A stain can point to a problem some distance away, so establish where water is entering or backing up before arranging a repair. Have defects dealt with before the next period of heavy rain. Leave any inspection that requires going onto the roof to someone equipped and trained to work at height.

By |2026-11-14T18:53:50+01:002024-03-03|Technology and applications|Comments Off on What to check on a metal roof after winter

Corrugated fibre cement roofing at a wall: planning the flashing

The junction of the roof slope with the wall requires more attention than a simple overlap of two sheets. Water runs off different surfaces here, and wind can force it under the flashing. Fibre cement sheets should end at a planned position, with adequate support and protection. Asbestos-free fibre cement will not seal such a junction with the corrugation alone. A detail is needed that takes into account the shape of the wall, the direction of fall and the layers of the roof and façade. The wall may run along the roof slope or be located above its upper edge. These situations have a different direction of run-off and require a different flashing geometry. At the side, water moves along the junction. At the top closure, the ends of the corrugations and any air outlet must be protected.

By |2026-11-16T00:08:40+01:002024-02-26|Technology and applications|Comments Off on Corrugated fibre cement roofing at a wall: planning the flashing

Energy renovation of urban buildings: specifying the details for each property

Thermal modernisation of several municipal buildings requires a common way of documenting the works, but separate solutions for their building envelopes. A school, a retail unit and a residential building may have different roofs, threshold heights, ventilation conditions and hours of use. In this guide, Izoprofil.pl shows how to prepare a schedule of details for ordering and handover: junctions at parapets, windows, outlets and service penetrations. PIR insulation is considered as a possible component of a specific layer build-up, requiring confirmation of application and material compatibility. Common inspection forms make it easier to compare quotes if they also include the differences between the buildings. Energy performance must then be assessed taking into account conditions of use and weather; the purchase of insulation alone is not proof of savings achieved.

By |2026-11-15T17:19:12+01:002024-02-26|Technology and applications|Comments Off on Energy renovation of urban buildings: specifying the details for each property

How should you plan the insulation of aerated concrete with PIR boards under render?

On an aerated concrete wall, the entire insulation system must be selected. The properties of the masonry, the type of PIR facing and compatibility with the render layer are important. Not every insulation board is suitable for such an application. The required thermal performance is set by the design, and the thickness results from calculations and the available details. Record the variant, thickness and declared properties of the blocks. The density and method of constructing the wall affect its parameters. A single thermal resistance should not be attributed to the entire group. Joints, renders and areas with other materials are also needed to assess the wall.

By |2026-11-14T09:33:20+01:002024-02-22|Technology and applications|Comments Off on How should you plan the insulation of aerated concrete with PIR boards under render?

What to check on your roof in autumn

An autumn roof inspection should begin by identifying which elements are most exposed to standing water and debris. Check above all that gutters, valleys and outlets are clear, and assess the condition of flashings at chimneys and walls. Do not rely on a ground-level view alone – inspect the roof from accessible, safe positions, noting displaced flashings, unevenness and loose items. Photographs from the previous season are helpful for spotting changes. Bear in mind that the scope of the inspection should match the roofing and the building's conditions.

By |2026-11-15T02:34:46+01:002024-02-18|Technology and applications|Comments Off on What to check on your roof in autumn

Straight or rounded ends for metal fence pickets? Differences that matter before ordering

The finish of a picket is a small detail that strongly influences the appearance of the fence. A straight cut tidies the top line, while a curve emphasises the rhythm of individual elements. The choice is not limited to taste, however. Not every profile offers all end variants. The installation direction and the way it is set into the system may also matter. Metal pickets should be ordered with an unambiguous description of both ends, rather than leaving this decision until delivery. The cross-section describes the spatial shape of the picket. The end finish refers to how its length terminates. The same profile may be available with a straight cut or a rounded top, if the range provides for it. This does not mean a change to the width or depth of the entire element. Both pieces of information should be sought separately in the documentation.

By |2026-11-15T17:18:35+01:002024-02-18|Technology and applications|Comments Off on Straight or rounded ends for metal fence pickets? Differences that matter before ordering
Back to top