About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

How to choose a roof colour that works with the façade

First establish which elements of the house will remain unchanged, and match the roof colour to them. During renovation, brick, stone, windows or fencing may outlast more than one coat of paint, so they set the palette. Also check gloss, texture and the sheet profile, as well as local requirements for the building's appearance. Before ordering, view a sample in daylight and at an angle close to the roof pitch. Make the final decision after comparing all permanent elements, not just a catalogue swatch.

By |2026-11-14T22:29:26+01:002023-11-11|Technology and applications|Comments Off on How to choose a roof colour that works with the façade

Will a mineral wool panel soundproof the hall, and how do you read its acoustic parameters?

A mineral wool core does not mean that every panel absorbs noise well inside the room. A panel with full steel facings can limit sound transmission while reflecting it back into the room. First you need to establish the problem: noise outside, between rooms or reverberation in the hall. Each requires a different approach. Insulation describes limiting the passage of sound through a partition. Absorption concerns the energy that does not return to the room as a reflection. These are different properties. Material hidden behind full steel sheet does not behave the same as an exposed or suitably protected absorbent layer.

By |2026-11-14T09:33:38+01:002023-10-29|Technology and applications|Comments Off on Will a mineral wool panel soundproof the hall, and how do you read its acoustic parameters?

Preparing your roof for snow, frost and winter weather

Winter roof preparation begins with deciding who will assess the need for snow removal and how it will be carried out, not with cleaning the gutters alone. Before the frost, repair loose flashings, damaged connections and active leaks before the weather makes access difficult. Also check the places where installation work was previously done, because openings left behind may only reveal a problem during lying snow and thaw. There is no single safe snow depth for all roofs – construction, weather conditions and actual load determine it.

By |2026-11-15T02:35:15+01:002023-10-28|Technology and applications|Comments Off on Preparing your roof for snow, frost and winter weather

Checking that flashings in one delivery match in material and colour

With a large order, flashings often come from several batches or arrive on site at different times. It is then easy to mix up the material, the surface finish or the colour side. One clear schedule limits the problem. It should describe each group of elements, from ridge caps to starter profiles. A joint delivery makes sense when all parts are easily identifiable and correspond to the approved specification. Ridge caps, barge flashings, gutter aprons and chimney flashings should be listed in separate rows. For each, add the cross-section, length and number of pieces. Starter profiles and other plinth elements should also be separated. This allows quantities to be checked without mixing the functions of similar profiles.

By |2026-11-15T02:36:48+01:002023-10-27|Technology and applications|Comments Off on Checking that flashings in one delivery match in material and colour

Why the cheapest covering can still mean a costly roof

What matters is whether you are comparing the cost of a complete roof, not just the price of a sheet. Check the coverage area, the type of coating and the scope of the offer, because a unit price without these details can be misleading. Also include accessories, transport, cutting and installation conditions, which may reverse an apparent saving. On a complex roof, flashings and accessories can account for a significant share, so it is worth comparing offers for your own project. Leave the final choice to the designer, who will assess whether the cheaper variant meets the required parameters.

By |2026-11-14T18:54:11+01:002023-10-24|Technology and applications|Comments Off on Why the cheapest covering can still mean a costly roof

Flat roof coverings: how to choose the right build-up

The choice of flat roof covering depends primarily on the geometry of the falls and the layout of the drains, not on the waterproofing material alone. Before laying the layers, check whether the design provides for the water flow path, substrate deflections and levels at parapets and service penetrations. Only then should the structural steel deck, PIR insulation and bitumen felt or membrane be selected as one system. A sandwich panel requires its own minimum slope, so it cannot replace an arbitrarily level assembly.

By |2026-11-14T18:52:57+01:002023-10-19|Technology and applications|Comments Off on Flat roof coverings: how to choose the right build-up

What do 100 metres of sheet metal cost? Linear metres versus square metres

The question about 100 metres of steel sheet requires clarification of the unit. One hundred linear metres is the sum of the lengths of the sheets, while one hundred square metres is the area. The result also depends on the overall width or coverage width. These figures must be established before comparing prices. Otherwise, two similar amounts may refer to different quantities of material. A linear metre means a length of 1 m at a specified width. Twenty sheets of 5 m each give 100 linear metres. This does not yet indicate what area will be covered. The effective width of the specific profile is needed, along with information on any longitudinal joints.

By |2026-11-14T12:00:46+01:002023-10-03|Technology and applications|Comments Off on What do 100 metres of sheet metal cost? Linear metres versus square metres

How often should a roof be inspected and what maintenance does it need?

Start with the covering instructions and the way the roof is used, because these set a realistic inspection plan. Check above all the drainage, fixings, flashings and sheet surface, rather than mechanically repeating annual painting or tightening every screw. A roof under trees needs different attention from an exposed slope, so link dates to leaf removal and preparing drainage for the rainy season. After strong wind or hail, do not wait for the scheduled inspection. Also decide who will assess the slope after another team has worked there.

By |2026-11-14T18:56:11+01:002023-09-30|Technology and applications|Comments Off on How often should a roof be inspected and what maintenance does it need?

Timber connectors: common types and where they are used

The choice of a carpentry connector is determined by the whole node, not by the shape of the fitting alone. Before buying, check what loads it is to transfer, what the geometry of the components is and in what environment the connection will work. The specified nails, screws or anchors and the installation pattern also matter. An angle bracket, beam hanger or post base may serve different functions, and a similar appearance does not guarantee interchangeability. The documentation gives parameters for a specific arrangement, so it is worth knowing the connection diagram and the conditions for which they were determined.

By |2026-11-14T22:27:00+01:002023-09-24|Technology and applications|Comments Off on Timber connectors: common types and where they are used

How the profile of cut-to-length and modular roof sheets affects the finished roof

The appearance of tile-effect metal roofing depends mainly on the shape of the wave, the height of the transverse pressing and the rhythm of the divisions. The method of delivery in long sheets or small panels is a separate feature. Cut and modular coverings can suit both a calm, traditional building form and a simple modern house. It is best to assess a larger fragment of the covering in daylight, from a similar distance as the finished roof. The profile has a division along the roof slope and a division across the sheet. The waves run lengthwise, and the transverse rhythm is formed by the steps of the pressing. The height of the wave itself need not equal the total height of the finished panel. When comparing technical data sheets, the drawing must be checked.

By |2026-11-14T15:40:57+01:002023-09-23|Technology and applications|Comments Off on How the profile of cut-to-length and modular roof sheets affects the finished roof
Back to top