About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

PIR or XPS for a flat roof: how to decide based on the layer build-up?

On a flat roof, the layer build-up is chosen first, and only then the insulation. PIR placed beneath the waterproof covering performs differently from XPS in an inverted roof. Moisture, load and the method of fixing all matter. A lower lambda alone does not confirm that the material is suitable as a substitute in an existing solution. In a classic roof, the insulation sits beneath the waterproof layer. In an inverted roof, the thermal insulation lies above the waterproofing. That is the fundamental difference in service conditions. A material in the upper position must be suitable for contact with water and for the intended method of draining precipitation.

By |2026-11-14T09:33:52+01:002023-07-20|Technology and applications|Comments Off on PIR or XPS for a flat roof: how to decide based on the layer build-up?

PIR when replacing the roof covering: insulating without losing loft space

Replacing the roof covering is an opportunity to insulate the roof slopes from the outside. PIR boards above the rafters can limit intervention in finished rooms. Before starting, the condition of the timber, the heights of the layers and the way the new roof connects to the existing façade must be checked. PIR boards laid above the rafters form a layer that also covers the wooden structural elements. This makes it possible to reduce their contribution to heat flow through the roof. The exposed structure allows areas previously inaccessible to be assessed. The new insulation should be placed on a prepared assembly with a confirmed technical condition. After removing the covering, the timber and the locations of earlier leaks should be inspected. The new layer should not conceal sections requiring structural repair.

By |2026-11-16T00:09:50+01:002023-07-17|Technology and applications|Comments Off on PIR when replacing the roof covering: insulating without losing loft space

Timber roof structures: components and construction principles

The roof structure transfers the weight of the covering, snow and wind action onto the walls and supports of the building. It is formed by interacting elements, not by the rafters alone. The choice of roof truss depends on the span, the room layout and the design. Before installing the metal sheeting, the geometry of the structure, the connections and the substrate under the covering must also be checked. Each element must correspond to its function within this system. The covering transfers loads onto the battens or purlins, and these onto the subsequent load-bearing elements. In a timber roof truss, part of this work is carried out by the rafters. The forces then pass to the wall plates, purlins, posts and walls, depending on the system. The continuity of this load path is important.

By |2026-11-14T15:39:39+01:002023-07-16|Technology and applications|Comments Off on Timber roof structures: components and construction principles

What is a roof valley and how can it be kept watertight?

A roof valley is the concave junction of two roof slopes that collects water from both adjacent surfaces and must allow it to drain freely. When assessing the workmanship, it is worth checking not only the flashing itself but above all the clear flow of the channel and the distance of the sheet edge from its centre line. This distance determines the drainage cross-section and is often the source of problems. Watertightness depends on the shape of the flashing, its support and correct laps, not on the amount of sealant. Even the best sealant will not repair a badly formed detail.

By |2026-11-14T22:27:42+01:002023-07-15|Technology and applications|Comments Off on What is a roof valley and how can it be kept watertight?

When is second-quality trapezoidal steel sheet worth buying?

Second-grade trapezoidal steel sheet can lower the cost of a small covering if it has identified defects and matches in dimensions. When buying, also inspect the edges, the underside and the overlap areas. What matters most is the cost of the sheets you will actually use. A discounted batch in random lengths will not always work out cheaper. A slight difference in shade means something different from a broken coating, a deep bend or a deformed edge. Ask for the reason for the markdown. Examine the sheet in light falling along the profile. This angle helps to spot waviness and dents. Also check the surface of the underside, especially if it will be visible inside.

By |2026-11-14T15:39:20+01:002023-07-11|Technology and applications|Comments Off on When is second-quality trapezoidal steel sheet worth buying?

How to reduce the risk of roof leaks

Limiting the risk of leaks depends above all on the pitch chosen for the specific roofing material, not on the thickness of the sheet metal alone. Check whether the slope on the actual structure meets the product's requirements, especially where the length of joints or the presence of openings changes the conditions of use. Plan the laps, supports and details at the chimney, valley or window before ordering. Remember that in roof panels a continuous panel differs from a system with a transverse lap. Inspect the installation in stages, before the layers are covered.

By |2026-11-14T18:56:13+01:002023-07-08|Technology and applications|Comments Off on How to reduce the risk of roof leaks

Collar beam roofs: structure, costs and limitations

A collar-tie roof is a structure of rafter pairs connected by transverse timber members called collar ties, whose position and connections directly shape how the entire roof truss performs. Before deciding, it is worth establishing whether the design allows the loft to be adapted without removing the collar ties, since this element often limits layout freedom. Check that the collar-tie-to-rafter connections match the solution assumed in the calculations — random screws or extra holes can weaken the timber. The choice of structure is governed by span, loads and how forces are transferred to the walls, not by a sketch alone.

By |2026-11-14T22:27:20+01:002023-06-26|Technology and applications|Comments Off on Collar beam roofs: structure, costs and limitations

Changing insulation during renovation: how to read a Kingspan offer

Selecting Kingspan insulation for a renovation begins with establishing what is actually present in the existing building element, not with the brand name in the offer. In old documentation, the brand is sometimes too general a clue, because Kingspan Therma TR26 and Therma TR27 are boards with a PIR core, while the Kooltherm family uses phenolic foam. The brand alone therefore does not identify the type of insulating material or the function of the layer. During the pre-renovation inspection, the product must be identified by its core, its facing and its intended place of application, especially when the project description gives only Kingspan without a specific family and variant. Only on this basis is the scope of demolition work and the method of preparing the old building element determined.

By |2026-11-16T04:49:58+01:002023-06-26|Technology and applications|Comments Off on Changing insulation during renovation: how to read a Kingspan offer

Comparing PIR, EPS, XPS and mineral wool for roof insulation

Begin comparing roof insulation with the required thermal resistance, not with board thickness. Check whether the chosen variant meets the project's fire, moisture and mechanical requirements. PIR with a lower lambda may need a thinner layer than EPS, XPS or mineral wool, which can matter where space is limited. For each product, establish the declared lambda and calculate R as thickness in metres divided by lambda. Only then compare the cost of the whole roof, including thermal bridges, fixings and flashings. Leave final thicknesses to the designer.

By |2026-11-15T02:34:51+01:002023-06-22|Technology and applications|Comments Off on Comparing PIR, EPS, XPS and mineral wool for roof insulation

How do you choose an insulated wall panel with a mineral wool core for a specific building layout?

The best wall panel is one that meets the building's requirements and can be installed correctly. Thickness alone does not determine the choice. Thermal, fire and load-bearing parameters must be checked. Dimensions are equally important. The panel module should work with the windows, door and support layout, rather than forcing random cuts. First define the function of the rooms, the temperature and the humidity conditions. Establish the fire protection and acoustic requirements. Only then compare specific panels. It is not worth choosing the thickest panel if the other properties still do not match the design.

By |2026-11-14T09:32:01+01:002023-06-19|Technology and applications|Comments Off on How do you choose an insulated wall panel with a mineral wool core for a specific building layout?
Back to top