What are sheet metal flashings and where does a roof need them?

Flashings are there to carry water through places where an ordinary roofing sheet does not provide continuity — at the edge of a slope or against an obstacle such as a chimney. When planning, the first thing to check is whether the profile of the flashing directs the flow onto the next drainage surface, rather than merely covering the edge. Equally important is whether the detail works together with the layer beneath the covering and does not close off the required airflow. The shape depends on the specific location, so the colour of the sheet alone is not enough.

By |2026-11-14T18:55:07+01:002022-06-03|Technology and applications|Comments Off on What are sheet metal flashings and where does a roof need them?

Trapezoidal steel sheets for cladding and structural use: how their roles differ

Trapezoidal sheeting serves one of two functions in a building: protective or structural, and the choice between them depends on whether it is to carry loads between supports or merely close the partition against the weather. It is worth checking the documentation for the specific profile, because the name T18 or T35 alone does not determine its use. Differences in steel thickness and rib shape affect load capacity, but only the design establishes whether a given sheet may work as a load-bearing element. The selection decision is left to the designer.

By |2026-11-14T22:29:02+01:002022-05-10|Technology and applications|Comments Off on Trapezoidal steel sheets for cladding and structural use: how their roles differ

When does a roof need repair and when does it need replacing?

The condition of the whole roof assembly and the cause of the fault, not the age of the covering, should determine whether to repair or replace. Before comparing costs, establish the water's path: it may travel along the membrane or flashing and appear far from the point of entry. Check whether the problem is limited and can be permanently removed, or whether it involves widespread corrosion, repeated leaks or damaged layers. Also distinguish a leak from condensation. A diagnosis from outside and from the accessible interior allows the scope of work to be matched to the actual cause.

By |2026-11-15T02:35:11+01:002022-04-28|Technology and applications|Comments Off on When does a roof need repair and when does it need replacing?

Z275 and other coatings for galvanised profiles. What should a buyer check?

A coating is often described in a quote with a single abbreviation. Behind that abbreviation, however, lie specific material properties and the principles for assessing them. When buying galvanised profiles, it is worth distinguishing the type of protection from the steel grade and thickness. These are separate parameters. A Z-profile, C-profile, sigma or omega may have the correct shape and yet not meet the requirements of the environment in which it is to work. The Z designation indicates a zinc coating. The number 275 refers to a specific required coating mass per surface area of the sheet, calculated for both sides together. It should not be interpreted as 275 micrometres, nor should this mass be attributed to each side separately. This is a common error when comparing quote descriptions.

By |2026-11-15T17:15:49+01:002022-04-26|Technology and applications|Comments Off on Z275 and other coatings for galvanised profiles. What should a buyer check?

Will roof panels available from stock fit the length of your roof?

A ready batch of sheets can speed up the purchase if it matches the roof dimensions. The total square metres alone do not confirm this. You need to know the length of each element, its profile and the preparation of the ends. Before choosing material available from stock, draw it on the actual supports and the edges of the roof slope. Measure along the slope, in line with the position of the panel. The horizontal projection is not the same as the length down the slope. Allow for the intended eaves and the termination at the ridge or wall. The dimensions should follow from a specific detail, not from an arbitrary addition to the measurement.

By |2026-11-14T12:01:49+01:002022-04-14|Technology and applications|Comments Off on Will roof panels available from stock fit the length of your roof?

What makes coated steel sheet suitable for roofing?

The choice of roofing sheet depends on how the entire layer system matches the building's conditions, not on colour or sheet thickness alone. It is worth checking the coating documentation, the product's intended use and the maintenance requirements, especially in coastal areas or near an industrial plant. The steel core provides mechanical properties, a metallic coating protects it, and the outer layers determine colour, texture and part of the environmental resistance. Their arrangement can vary, so two similar-looking sheets may behave differently under prolonged moisture or scratching.

By |2026-11-14T22:28:00+01:002022-04-07|Technology and applications|Comments Off on What makes coated steel sheet suitable for roofing?

Roofs without overhangs: design, advantages and detailing challenges

A roof without eaves is a system in which the slope ends at the façade rather than projecting beyond the wall. Before choosing this variant, check above all the roof-edge cross-section: the junction of covering, insulation and drainage. This detail determines whether water reaches the gutter rather than the wall or the space behind the insulation. It is also worth establishing how ventilation under the covering will work and whether service access to the gutter is provided. A visualisation alone will not show these details, so the design should clearly define the solution for each layer.

By |2026-11-14T22:26:39+01:002022-04-03|Technology and applications|Comments Off on Roofs without overhangs: design, advantages and detailing challenges

Finding the cause of a roofing sheet defect before making a claim

Before making a claim about roofing sheets, identify where the fault occurs. A problem across a whole slope calls for a different investigation from a leak at a single junction. Record the extent of the damage, when it appeared and how the sheets were stored and installed. Colour variation, rippling, leaks and rust spots can have different causes. For example, small particles of steel from drilling or cutting can rust on the surface. Keep the labels and document the condition of the roof before cleaning it.

By |2026-11-15T02:35:45+01:002022-03-31|Technology and applications|Comments Off on Finding the cause of a roofing sheet defect before making a claim

What to look for in modular tile-effect roofing and when to use it

A good modular metal roof tile stands out for its repeatable shape, suitable coating and clear installation instructions, but it does not guarantee less waste in every project. Before choosing, compare the cutting layout, number of joints and full covering cost for your roof. The module is only a sheet format, while the durability of the roof depends on the entire system of materials and workmanship. Check whether the small sheets really make work easier around dormers and valleys, and whether their geometry suits the roof slope.

By |2026-11-14T18:54:36+01:002022-03-21|Technology and applications|Comments Off on What to look for in modular tile-effect roofing and when to use it

How is a four-sided hipped roof constructed?

You can recognise a hip roof by its four slopes and the absence of gable walls, but its construction and costs are determined above all by the building's plan. Before choosing the covering, check whether the slopes form two trapezoids and two triangles, or whether they meet at a single point on a square plan. Send the plan and sections to the contractor rather than relying on the colloquial name. Compare the sheet cutting layout, the length of the hips and the number of flashings, because the roof area alone is not enough for a reliable estimate.

By |2026-11-14T22:27:40+01:002022-03-07|Technology and applications|Comments Off on How is a four-sided hipped roof constructed?
Back to top