Technology and applications2026-11-15T17:17:10+01:00

Choose a product group

Metal roofing

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Technology and applications

Izoprofil.pl explores how building materials work together. Sandwich panels, PIR insulation and trapezoidal sheets depend on their supports, joints, fixings and drainage. The guides explain how product properties affect use on roofs, walls and insulation assemblies. They help you read the documentation, identify limits and prepare questions for your designer or contractor. You can also look up detailing, common faults and preparing materials for installation. Use the technical issue on your project to choose an article, then check the instructions for your specific product. Similar-looking components may have different requirements.

What purlins and side rails do in a steel-framed building

Purlins and wall rails look modest next to the large frames of a steel hall. They are usually lighter than the frames and have thin walls. Yet the roof covering and the wall cladding often rest on them. Their selection affects the load-bearing capacity of the building envelope, deflections and the stability of parts of the skeleton. The profile name or its height alone is not enough to assess suitability. Purlins run between the main roof beams and support the covering. Wall rails transfer actions from the cladding to the columns. Loads include self-weight and wind action, and on the roof also other anticipated actions. In a steel hall, the sub-structure must therefore match both the geometry and the way the building is used.

Reading a metal fence picket data sheet: what the figures mean

The product data sheet should make it easier to compare fence pickets and prepare an order. Sometimes, however, it contains abbreviations that are easy to misread. The strip width before profiling is not the width of the finished component. The maximum production length does not mean the span without supports. Such distinctions have a direct impact on the quantity of material and the method of installation. Metal fence pickets should only be selected after combining the data from the table, the drawing and the instructions. Each of these sources answers slightly different questions. Also check the document version marking. An older catalogue and the current offer may describe different variants, so discrepancies should be clarified before accepting the parameters.

EPS, XPS or PIR: how to choose insulation by application

The three abbreviations denote different families of insulation. Each includes products with different purposes and parameters. The choice should follow from the installation location, moisture and load. Only then should thickness and price be compared. Good insulation under plaster need not be the right material under a loaded floor. EPS is expanded polystyrene. Its structure consists of bonded granules. XPS is produced by extrusion and has a different, closed-cell structure. PIR is rigid polyisocyanurate foam, often supplied with facings. They should not be treated as one material in different colours.

Installing insulated roof panels: from checking the supports to inspecting the flashings

roof panel installation begins before the first component is lifted. The structure, slope and completeness of details must be checked. The laying direction, seals and correct fixing then matter. A well-planned sequence allows joints to be closed before the next sheet obscures access to them. Check the spacing, width and plane of the supports. Compare actual dimensions with the panel selection. The structure should be ready for installation, with work that could damage the coatings completed. Sheets must not be pulled to crooked purlins using greater screw force.

How roof pitch affects the choice of roof covering

The choice of roofing is determined by the actual roof pitch, not by the profile type alone. Before ordering T18 or T35 sheeting, modular metal tiles or insulated roof panels, check whether the pitch falls within the range permitted for the specific product and its details. Distinguishing degrees from percentages is essential: a 5% slope corresponds to an angle of about 2.86°, not 5°. Confusing the units can lead to a solution outside the instructions. It is also worth establishing whether the measurement refers to the horizontal projection or the length along the slope.

Are concealed gutters a good fit for a metal roof?

Concealed gutters can suit a house with a metal roof well, especially with a simple building form and restrained eaves detail. Their selection, however, requires the drainage to be designed in advance. The masking fascia must not restrict access for cleaning, and the outlet must be matched to the roof surface area. First, the route of water, ventilation and insulation must be established. Only then is the colour of the visible elements chosen. Various solutions appear under the name concealed gutters. Sometimes only the gutter behind the masking fascia is concealed, while the downpipe remains on the façade. In another arrangement, the outlet is also concealed within a suitably prepared wall zone. These variants should not be treated identically.

Back to top