About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

How many ridge caps should you order for a metal roof?

The number of ridge caps is best established on a plan of all ridges and then verified by measurement. Dividing a single length by the product's nominal dimension gives only an approximate result. The order must account for joints, end pieces and differences between roof sections. It is also worth separating the quantity of sheet metal from the scope of installation. A well-described set reduces interruptions caused by the lack of one short element. On a simple roof, one section may be sufficient. With a complex roof shape, there are more ridges and not all have the same profile. The most convenient approach is to mark them on a sketch with consecutive symbols. For each, note the length, adjacent slopes and how both ends are finished.

By |2026-11-15T02:36:26+01:002024-08-02|Technology and applications|Comments Off on How many ridge caps should you order for a metal roof?

BauderPIR M/MF when replacing roof layers

During the roof renovation, boards with a matt mineral fleece were partially exposed. Before supplementing the M/MF, it is worth identifying the old variant and the condition of its surface. A similar thickness of the new material does not confirm an identical thermal resistance or compatibility with the covering. The boundary of the repair should have a clearly described junction between the two parts. In a renovation, the area described as a roof with a PIR board with a mineral facing requires the old layers to be identified. The first difficult place to inspect is the area of fleece beneath the waterproofing layer. It is not worth determining the thickness of BauderPIR M/MF solely on the basis of an old drawing. The measurement should cover the thickness of the insulation being ordered and the condition of the substrate beneath the covering, taking into account changes made during earlier work.

By |2026-11-16T00:11:19+01:002024-07-15|Technology and applications|Comments Off on BauderPIR M/MF when replacing roof layers

Single- or double-module roof sheets: when does a smaller sheet help?

A single-module sheet and a double-module sheet differ in the number of transverse profile rows. The smaller format can make work easier on short roof slopes and where there are many breaks. The larger one allows more roof to be covered with a single element. Neither is always cheaper or simpler to install. The choice requires comparing the cutting layout, the coverage area, handling and the joining rules in the specific system. A module is a repeating section of the profile, defined by the division of the transverse pressings. It is not a universal length for the whole market. In one family it is, for example, 350 mm, but another model may have a different division. The length of the finished sheet is supplemented by the sections needed to make the laps and finish the edges.

By |2026-11-14T15:40:55+01:002024-07-04|Technology and applications|Comments Off on Single- or double-module roof sheets: when does a smaller sheet help?

Installing modular tile-effect metal roofing

Installation of modular tile-effect metal roofing begins with checking the structure and the eaves detail. Then the layers under the covering, the substructure and the sequence of laying the sheets are prepared. The dimensions of the battens, the direction of installation and the fixings depend on the specific system. The following guidelines help to plan the works and the acceptance. They do not replace the instructions of the supplied product or the roof design. Check the geometry of the roof slopes, the eaves line and the position of the openings. The evenness of the substrate matters for the assembly of the seams and the appearance of the surface. If the diagonals or the plane deviate from the assumptions, the problem must be resolved before covering. The sheets should not be used to straighten a poorly made structure. Tightening too firmly with a screw can leave a permanent deformation.

By |2026-11-14T15:40:38+01:002024-06-30|Technology and applications|Comments Off on Installing modular tile-effect metal roofing

Choosing PIR wall panel thickness when insulation and space both matter

The thickness of a wall PIR panel affects both insulation performance and the dimensions of details. It is not worth choosing it solely by price or by the limited width of the plot. First, the thermal, fire and structural requirements must be established. Only then should you check how the panel will fit at the plinth, around openings and at the boundary of the available space. To assess a panel, its thermal transmittance is used, described accordingly in the data for the variant. Lambda refers to the material, and the R-value of a layer is not the same as the U-value of the complete building envelope. These figures should not be compared in one column without explanation.

By |2026-11-14T12:01:04+01:002024-06-24|Technology and applications|Comments Off on Choosing PIR wall panel thickness when insulation and space both matter

BauderPIR T and ponding water: preparing for roof renovation

After the old covering has been removed, the valley line runs differently from the retained drawing. The BauderPIR T layout must be updated to match the actual substrate. Random wedges should not be reversed merely to level the field visually. The fall directions and the level of the outlet must be checked before the roof area is closed again. In a renovation, the area described as a roof with uncoated tapered boards requires the old layers to be investigated. The first difficult place to inspect is the valley that carries water towards the outlet. The thickness of BauderPIR T should not be determined solely on the basis of an old drawing. The measurement should cover the elevations of the substrate and the course of the lines collecting water, taking into account changes made during earlier work.

By |2026-11-16T00:11:21+01:002024-06-22|Technology and applications|Comments Off on BauderPIR T and ponding water: preparing for roof renovation

Clay tiles or tile-effect steel roofing: what to check before choosing

The choice between ceramic tiles and metal roofing depends on compliance with the design and the required roof pitch, not on the appearance of a sample. Check whether both coverings fall within the pitch limits given by the manufacturer for the specific product, since a single limit for the whole category does not exist. A shallow roof may need additional layers under the covering, which changes the cost and scope of work. Also analyse the load-bearing capacity of the roof structure, the fixing method, the full cost estimate including flashings, and local requirements for the building's appearance.

By |2026-11-14T22:28:20+01:002024-06-20|Technology and applications|Comments Off on Clay tiles or tile-effect steel roofing: what to check before choosing

How to refresh the appearance of a metal roof

Begin by establishing whether the deterioration in appearance affects the entire roof slope or only the areas around the chimney, branches or installations. A recurring run-off mark often points to the source of soiling higher up, so cleaning alone will give a short-lived effect if the cause is not corrected. Before commissioning a renovation, look at close-ups of different sections of the roof to distinguish deposits from damaged coating and to check tightness. Choose the scope of work after inspection, taking the type of steel finish into account.

By |2026-11-14T18:55:08+01:002024-06-15|Technology and applications|Comments Off on How to refresh the appearance of a metal roof

When are insulated sandwich panels a good fit for a roof?

A roof sandwich panel combines steel facings with an insulating core and, in a properly selected system, allows the roof to be closed and insulated quickly. When choosing, check above all whether the specific panel has been tested for loads, heat and fire and whether its joints, fixings and flashings match the design. The core type alone, such as PIR or mineral wool, does not determine the product's suitability, nor does its external appearance. Leave the decision on support spacing and sealing to the designer, as these depend on the system and the building conditions.

By |2026-11-15T02:34:34+01:002024-06-11|Technology and applications|Comments Off on When are insulated sandwich panels a good fit for a roof?

Designing modern façades with sheet metal and sandwich panels

The key to a modern building form is a disciplined division of surfaces, not the choice of sheet metal or sandwich panels alone. Readers should first check the proportions of the roof, walls and openings, and draw the layout of sheets and panels together with the joinery, because a regular material exposes every inconsistency, such as a narrow offcut at a corner. The role of each layer is equally decisive: roof covering, wall panel and separate insulation have different tasks, and their combination should reconcile appearance with drainage, thermal insulation and load-bearing capacity.

By |2026-11-14T18:54:15+01:002024-06-01|Technology and applications|Comments Off on Designing modern façades with sheet metal and sandwich panels
Back to top