About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Where do sandwich panels and PIR insulation fit into modern construction?

An insulated panel can close a wall or roof while reducing heat loss. A separate PIR board is used to insulate a building element that has its own structure and covering. These materials make construction easier, but they are not interchangeable. The choice is determined by the building's function, the support layout, moisture and fire requirements. The greatest benefit comes from selecting the whole solution before ordering materials. An insulated panel has two metal facings bonded to an insulating core. The components work together when carrying loads. As a result, the finished panel can form the envelope of a hall, workshop or warehouse. It still requires designed supports, however. The term self-supporting does not mean it will replace columns, purlins and the entire building structure.

By |2026-11-14T15:40:52+01:002022-02-18|Technology and applications|Comments Off on Where do sandwich panels and PIR insulation fit into modern construction?

Roof valleys in fibre cement roofing: why they need a separate detail

The valley is one of those places where a simple roof stops being simple. Water flows into it from the adjacent roof slopes, and the diagonal cuts change the shape of the sheets. Fibre cement sheets must be planned here with account taken of the support and the drainage. Asbestos-free fibre cement should not be cut at the valley only when there is no room left for the next row. A separate detail makes it possible to assess the tightness, the fixings and the later possibility of cleaning. An ordinary corrugation trough carries precipitation away from a narrow strip of roof. Water from many such strips on both sides reaches the valley. The size of the flow depends on the geometry of the roof slopes and on the rain conditions.

By |2026-11-16T00:08:41+01:002022-02-10|Technology and applications|Comments Off on Roof valleys in fibre cement roofing: why they need a separate detail

How to assess the environmental impact of a metal roof

A metal roof can be a sensible environmental choice if it is well specified, durable and uses material sparingly. When assessing an EPD, the first thing to check is whether the declared unit and material variant match the actual roof build-up, not just the thin sheet. It is equally important to establish which life-cycle stages the calculations include. Only on that basis can solutions with the same function be compared, bearing in mind that heat loss depends on the whole assembly rather than the covering alone.

By |2026-11-14T18:53:53+01:002022-02-06|Technology and applications|Comments Off on How to assess the environmental impact of a metal roof

PIR in wall renovation: reveals, old render and internal insulation

Façade renovation often reveals limitations at windows, the plinth and the roof. A thin PIR board can help resolve selected details. First, however, the substrate and moisture must be assessed, and then a finishing system suited to the board being ordered must be selected. PIR boards can form a continuous layer of thermal insulation on the outer side of the wall. This position helps reduce thermal bridges associated with structural elements. An uninsulated ring beam can remain a weak point despite a good layer in the field. The new scope should include a continuous connection over the full height of the wall. When renewing a façade, it is worth checking the places that were not previously insulated. This may be the ring beam, the strip near the roof or the space behind services.

By |2026-11-16T00:09:55+01:002022-01-30|Technology and applications|Comments Off on PIR in wall renovation: reveals, old render and internal insulation

Why metal cladding and sandwich panels work well on façades

Profiled sheet and sandwich panels work well on façades because they allow a repeatable layout and a coating suited to the surroundings, but they differ in function: a single sheet forms a screen, while a panel combines facings with an insulating core. Before ordering, it is worth drawing out the divisions, since a small shift of the first sheet changes the width of cut pieces at both corners. Also check the corners, openings and lower edge, where the material meets other parts of the building. Regular profiles and cover widths make it easier to fit the layout to the rhythm of windows, doors and structural columns.

By |2026-11-14T18:55:34+01:002022-01-26|Technology and applications|Comments Off on Why metal cladding and sandwich panels work well on façades

Checking the supporting structure for unevenness before laying sheets

An uneven roof is not always caused by warped sheets. The problem often starts earlier, at the battens or purlins. Fibre cement boards must be supported in accordance with the design and the installation instructions. They are not meant to be used to straighten the supporting structure by force of the fasteners. Asbestos-free fibre cement is a rigid material, so point loads and forced bending can lead to damage. Checking the plane before covering saves having to strip the roof slope later. From the ground you can see the line of the lower edge, but not the entire surface of the supports. Battens may be twisted and purlins locally deflected. The position along and across the roof matters. The required tolerances and the measuring method should be taken from the documentation for the specific system.

By |2026-11-16T00:08:45+01:002022-01-24|Technology and applications|Comments Off on Checking the supporting structure for unevenness before laying sheets

How can T8 trapezoidal steel sheet be used on façades, soffits and light cladding?

T8 is a sheet with a low profile, usually associated with façades, soffits and cladding. It gives a subtle surface texture. However, it should not be selected on appearance alone. Thickness, coverage and support are important. On a small wall, it is worth planning the divisions at windows and the width of the edge sections in advance. The number refers to a profile height of approximately 8 mm. It does not describe the thickness of the steel core. An example variant has an overall width of 1220 mm and an effective width of 1156 mm. Other products with a similar name may differ in cross-section and coverage width.

By |2026-11-14T09:31:35+01:002022-01-20|Technology and applications|Comments Off on How can T8 trapezoidal steel sheet be used on façades, soffits and light cladding?

What to include on a drawing for a made-to-order flashing

An elaborate graphic design is not always needed to order a non-standard flashing. What is needed, however, is unambiguous data. A clear cross-section with dimensions and a material description is more useful than an attractive view without scale. It is worth preparing such a drawing in a consistent layout. It makes quoting, confirming bending feasibility and later acceptance of the components easier. The drawing should show the shape after bending. Each leg is given a dimension, and bends requiring a specific angle are described. No part should be left as more or less horizontal. The person preparing production must know what result is to be achieved.

By |2026-11-15T02:37:03+01:002022-01-20|Technology and applications|Comments Off on What to include on a drawing for a made-to-order flashing

Measuring the eaves before ordering gutter aprons

Measuring the eaves should show not only their length but also the space between the covering and the gutter. Gutter aprons must fit this cross-section and direct water in the intended direction. When ordering, it is worth separating straight sections, corners and ends. An accurate sketch makes quoting easier and reduces the number of reworks. It is also needed when we plan to use a popular catalogue profile. Before measuring, the type of covering and the method of fixing the gutter must be established. Its position relative to the end of the roof slope is important. The gutter apron should correspond to the arrangement that will actually be installed. A measurement taken before changing the gutter may become outdated.

By |2026-11-15T02:36:42+01:002022-01-02|Technology and applications|Comments Off on Measuring the eaves before ordering gutter aprons

What determines rafter size and spacing?

The rafter cross-section is not selected from a single table that applies to every house. You need the span, spacing, timber class, loads and support scheme. Deflection and connections also matter. Ready-made advice such as "a rafter of this size is enough under metal roofing sheet" leaves out far too much information. Below we explain what influences the selection and when the design needs to be reassessed. The design span does not have to be the total length of the rafter. It depends on where the rafter is supported. A rafter supported only at the eaves and the ridge behaves differently from one supported by an additional purlin. On top of that come the overhangs beyond the walls. The designer must know where the forces are transferred into the structure of the storey below.

By |2026-11-14T15:39:41+01:002022-01-02|Technology and applications|Comments Off on What determines rafter size and spacing?
Back to top