BauderPIR FA when adding insulation to an existing roof

The replacement of the insulation with FA is carried out in stages while part of the covering remains in place. Large boards must be laid out so that they do not obstruct the temporary closure of the working boundary. The measured survey should allow for the laps and the irregular perimeter of the exposed area. The nominal rectangle taken from the original drawing may not match the actual cutting layout. In a refurbishment, the area described as the insulation of a large, regular roof field requires an investigation of the old layers. The first difficult point to inspect is the milled edge of the large-format board. The thickness of BauderPIR FA should not be determined on the basis of an old drawing alone. The measurement should cover the area of the actual covering and the widths of the strips at the perimeter, allowing for changes made during earlier work.

By |2026-11-16T00:11:16+01:002025-03-06|Technology and applications|Comments Off on BauderPIR FA when adding insulation to an existing roof

What to check in the attic before converting the roof for photovoltaics?

The attic says a great deal about the condition of the roof before it is converted for photovoltaics. Stains, a smell of damp, unevenness and traces of repairs help establish the scope of work. It is worth inspecting them before ordering the covering, not only once it has been removed. A BIPV system can give the house a new function and a coherent appearance. It will bring the greatest benefit when the renovation also resolves earlier problems hidden beneath the roof slope. The areas around chimneys, roof windows and the junctions between the roof slope and the walls must be inspected. Water marks may indicate a leak, but are sometimes associated with condensation. The conditions in which they appear are important. Information on whether a stain grows after rain, during a thaw or on cold days helps the person assessing the roof identify a possible cause.

By |2026-11-15T17:19:30+01:002025-02-28|Technology and applications|Comments Off on What to check in the attic before converting the roof for photovoltaics?

Sigma or channel sections? Comparing cold-formed steel profiles

A more complex cross-section is not necessarily the best in every structure. Sigma profiles have additional web bends, while C-sections have a simpler geometry. Both solutions can be useful if they match the working conditions. However, a reliable comparison requires a common task. You need to know the span, loads, support method and expected use. Only then do mass and price start to say something about cost-effectiveness. Roof purlins should be compared with purlins of the same required function. A wall rail working in a different arrangement is not a good reference point. The spacing of elements is also important. A lighter single profile does not have to mean a lower mass for the whole structure if more of them have to be used.

By |2026-11-15T17:15:46+01:002025-02-27|Technology and applications|Comments Off on Sigma or channel sections? Comparing cold-formed steel profiles

How many panel fasteners do you need when the fixing pattern varies?

There is no single number of screws per metre of panel that suits every wall and roof. Fixings are determined by loads, the panel and the structure. They are counted at points of support and connection. A figure per m² can help with a schedule, but only after the selection has been made. It should not serve as a ready-made layout instruction. The main fixings transfer loads from the panel to the supports. Other screws may connect the intended parts of the lap, and yet others fix the flashings. These are not freely interchangeable elements. Counting them all as one item makes it harder to check whether the set is correct.

By |2026-11-14T12:00:53+01:002025-02-27|Technology and applications|Comments Off on How many panel fasteners do you need when the fixing pattern varies?

How roof shape affects the number of slopes and junctions on a house

The roof shape is chosen primarily to suit the building's form, the attic's needs and local provisions, not the covering alone. It is worth checking whether the chosen arrangement of slopes allows the interior and drainage to be planned sensibly. A simple gable roof may be clear in structural terms, but it is not always the cheapest in every project. With a mono-pitch roof, water runoff and wall heights must be assessed. For a usable attic, the cross-section of the rooms is key, not the floor area alone.

By |2026-11-15T02:33:44+01:002025-02-23|Technology and applications|Comments Off on How roof shape affects the number of slopes and junctions on a house

Choosing a coating for steel roofing to suit the site

The answer is that matching a protective coating for sheet metal begins with identifying the building's surroundings and how it is used, not with colour. Readers should check the full finish designation, documentation of environmental restrictions and the scope of the guarantee before comparing offers. The shade alone does not describe resistance to moisture, sunlight or pollution. It is worth establishing whether the roof is near the sea, an industrial plant or places that stay wet for long periods. This information should be given to the seller before choosing a variant.

By |2026-11-15T02:34:28+01:002025-02-18|Technology and applications|Comments Off on Choosing a coating for steel roofing to suit the site

What are roof battens and when are they needed?

Battens provide support for the covering and a fixing point. Their spacing depends on the selected product, and their cross-section also on the structure and loads. Counter-battens serve a different function and in a typical roof with tile-effect metal roofing they help create a ventilation space. A correct batten grid must be level, stable and in accordance with the covering manufacturer's instructions. A battening error cannot be fixed simply by tightening the sheet more. In a typical pitched roof, battens run perpendicular to the direction of water runoff and support the sheets. Counter-battens are usually laid along the rafters. They separate the battens from the underlay and create an air path beneath the covering. Both elements work together, but their order cannot be freely swapped nor can one of them be removed.

By |2026-11-14T15:40:03+01:002025-02-14|Technology and applications|Comments Off on What are roof battens and when are they needed?

Adding Thermano Deck insulation to an existing roof: where to start

An old roof may have an uneven substrate, damp layers or flashings that are too low. These conditions must be assessed before insulating with Thermano Deck. Only then can the thickness be selected and a decision made as to whether the renovation will also cover the falls and drainage. Thermano Deck has a PIR core and a multi-layer, gas-tight facing containing aluminium on both sides. The product is intended, among other things, for classic flat roofs. During the pre-renovation inspection, check the large field of a flat roof based on trapezoidal sheet metal and finished with parapets. Thermano Deck must be selected together with the vapour control layer, the substrate and the method of executing the waterproofing before the scope of demolition is determined and the old building element is prepared.

By |2026-11-16T00:10:26+01:002025-02-14|Technology and applications|Comments Off on Adding Thermano Deck insulation to an existing roof: where to start

IKO enertherm ALU TAP when improving roof drainage

Changing the position of the outlet in a roof being renovated affects the layout of ALU TAP. It is not enough to move a single wedge to a new location. It is worth checking the boundaries of the fields, their heights and the drainage directions. Only an updated plan allows the elements needed to supplement the existing insulation to be determined. During the renovation, the scope described as a roof with aluminium tapered boards of various slopes requires the old layers to be identified. The first difficult place to inspect is the junction of fields with a different drainage direction. It is not worth determining the thickness of IKO enertherm ALU TAP solely on the basis of an old drawing. The measurement should cover the height difference between the ends of the wedge and the length in the direction of the slope, taking into account changes made during earlier work.

By |2026-11-16T00:11:38+01:002025-02-13|Technology and applications|Comments Off on IKO enertherm ALU TAP when improving roof drainage

How long does it take to build a house and what causes delays?

The construction time of a house depends on the documentation, the technology, the availability of crews and the sequence of works. It cannot be reliably determined with a single figure for every project. The roof is one of the stages that link the structural works with making the building weathertight. The schedule should account for deliveries, inspections and technological breaks. Below we show how to identify the points most exposed to delay. The calendar must include the preparation of the design and the formalities, not just the crew's working days. The scope of documents depends on the investment. If the plan requires additions or a change of assumptions, subsequent dates may shift. Ordering material before the design is finalised can be risky, especially when it is to be made to a specific dimension.

By |2026-11-14T15:40:34+01:002025-02-08|Technology and applications|Comments Off on How long does it take to build a house and what causes delays?
Back to top