Choosing the roof pitch before ordering insulated panels

The roof pitch must be determined together with the panel type and the layout of its joints. Percentages do not mean the same as degrees. The length of the roof slope, the support heights and the method of water drainage are also needed for the order. The term 'mono-pitch roof' alone is not enough to correctly select the material and prepare the flashings. Pitch in percent describes the ratio of the height difference to the horizontal distance. It is not divided by the panel length measured along the slope. First, determine two points on the same line of water flow. Record their elevations and the horizontal distance. Measuring the edge of the flashing alone can be misleading, because its top line does not have to coincide with the plane of the covering.

By |2026-11-14T15:38:30+01:002024-01-08|Technology and applications|Comments Off on Choosing the roof pitch before ordering insulated panels

How should you prepare the route for PV cables in a finished house?

In a finished house, the route for the cables from the photovoltaic roof should be planned before renovation work begins. What matters is installation safety, the tightness of the building envelope and limiting later chasing. Integrated roofing offers an opportunity to coordinate the roofing work with the electrical work. Cables can be routed through agreed locations before the roof is closed. First, however, the entire connection path must be established, right through to the relevant devices and the distribution board. The shortest distance is not always the best installation route. The conditions for routing the cables, the penetrations through building components and the ability to inspect them must be taken into account. Temperature, moisture and the risk of mechanical damage also matter. The designer should assess the entire route, not just a straight line from the roof slope to the technical room.

By |2026-11-15T17:19:49+01:002024-01-05|Technology and applications|Comments Off on How should you prepare the route for PV cables in a finished house?

Preventing corrosion on metal roofing, from cut edges to repairs

Protecting a metal roof against corrosion depends above all on whether the chosen coating suits the actual conditions around the building and beneath the covering. It is worth checking the coating's intended use, how edges and fixings are protected, and whether water can drain freely, rather than relying solely on the thickness of the coloured layer or the length of the guarantee. Moisture, contamination and lingering metal filings increase the risk. Regular inspection of details and prompt repair of minor damage using a method permitted for the given surface help catch problems at an early stage.

By |2026-11-15T02:33:42+01:002024-01-02|Technology and applications|Comments Off on Preventing corrosion on metal roofing, from cut edges to repairs

How to spot panel installation errors before they are covered up?

Some errors are visible immediately, but others disappear under the next panel or flashing. Inspection should therefore accompany installation. It is worth checking geometry, support, seals and the condition of coatings in a set order. A final look at a neat façade will not tell you everything about the quality of hidden joints. The cause may be taking the dimension of the structural axis instead of the length resulting from the detail. Another problem is omitting the plinth, eaves or corner thickness. Before ordering, it is worth comparing the plan, section and actual measurement. Each shows a different part of the geometry.

By |2026-11-14T12:01:27+01:002023-12-22|Technology and applications|Comments Off on How to spot panel installation errors before they are covered up?

How do you choose insulation for a house made of ceramic blocks to suit the wall thickness?

A wall made of ceramic blocks does not have a single common thermal parameter. What matters is the type of block, the wall thickness and how the joints are made. Insulation is selected only on this basis. In practice, it must also fit at the windows, the eaves and the plinth. Choosing the number of centimetres alone does not complete the design. In a new house, refer to the material schedule and check what was actually built in. In an older building, an inspection opening at a window or door opening can help. Do not determine thermal properties solely from the colour of the ceramic. Blocks of similar appearance may have a different arrangement of voids and a different purpose.

By |2026-11-14T09:33:15+01:002023-12-21|Technology and applications|Comments Off on How do you choose insulation for a house made of ceramic blocks to suit the wall thickness?

Ordering galvanised Z-sections takes more than a height measurement

“I need a Z-section of a given height” is a common way to start an enquiry. But further information should follow. Z-sections with a similar external dimension can differ in flange width, thickness and lips. The hole layout may also be different. If the profile is to work with an existing element or fit into a lap, these details become decisive. A good order describes the entire cross-section and its function. The opposing arrangement of the flanges creates the characteristic Z shape. In many systems their widths are deliberately different. This allows suitably matched sections to be joined by sliding the narrower part into the wider one. This detail must be taken from the documentation for the specific solution. Not every Z-profile has identical proportions.

By |2026-11-15T02:37:07+01:002023-12-17|Technology and applications|Comments Off on Ordering galvanised Z-sections takes more than a height measurement

Profiled tile-effect metal roofing: characteristics and applications

The suitability of profiled metal roof tiles depends on the steel parameters, coating and installation instructions for the specific solution, not on the wave shape alone. Before buying, it is worth checking the cross-section and side view to distinguish wave height from step height. You should also confirm the minimum roof pitch required for the given profile and assess the number of obstacles, such as valleys, chimneys and windows, which may influence the choice of sheet format.

By |2026-11-14T18:56:39+01:002023-12-15|Technology and applications|Comments Off on Profiled tile-effect metal roofing: characteristics and applications

IKO enertherm MG in renovation beneath synthetic membranes

When the old membrane is removed, the MG boards are exposed with the fleece locally damaged. The condition of the surface must be assessed before choosing how to reinstate the covering. The appearance of the core alone does not decide whether a board can be reused. The repair should take account of the requirements of the new layer and the extent of the actual damage. In a renovation, the scope described as a flat roof under a synthetic membrane requires an investigation of the old layers. The first difficult place to inspect is the interface between the membrane and the fleece facing of the boards. It is not worth determining the thickness of IKO enertherm MG solely on the basis of an old drawing. The measurement should cover the thickness of the insulation and the condition of the surface before the covering is installed, taking into account changes made during earlier work.

By |2026-11-16T00:11:39+01:002023-12-13|Technology and applications|Comments Off on IKO enertherm MG in renovation beneath synthetic membranes

Choosing trapezoidal steel sheets for a façade

First decide whether the trapezoidal sheet is only a screen for a ventilated façade or part of another designed wall assembly — this determines the subframe and details. Check the steel thickness, coating, cover width and sheet orientation, not just the rib height. Inspect the cross-section and confirm that the coated side faces the exterior. Assess the profile choice on a larger section of wall, with windows and corners, because a small sample does not show the proportions.

By |2026-11-14T18:55:10+01:002023-11-30|Technology and applications|Comments Off on Choosing trapezoidal steel sheets for a façade

Made-to-length tile-effect metal roofing for traditional houses

Base the choice of cut-to-size metal roofing on the building's form rather than on a catalogue pattern alone. Begin by checking whether long sheets will genuinely simplify covering straightforward slopes or instead force numerous cuts at dormers and breaks. The final effect depends on the rhythm of the profiles, the colour and the edge finish, so compare a sample with the actual boarding, joinery and flashing in daylight. Before ordering, confirm on the built structure the lengths of slopes, eaves, ridges and hips, and analyse the cutting plan against a modular variant.

By |2026-11-14T18:54:30+01:002023-11-24|Technology and applications|Comments Off on Made-to-length tile-effect metal roofing for traditional houses
Back to top