Fixing sandwich panels to masonry: how to provide adequate support

Masonry can be the substrate for panel cladding, but a proper connection detail is needed. It is not enough to drill through the panel with any anchor. The substrate must be assessed, loads transferred and space for fixings provided. Evenness of supports and sealing at the base and openings are also important. Determine the type of masonry units, their condition and the bond pattern. Solid brick, hollow block and aerated concrete require different approaches. Do not choose an anchor solely by the appearance of the render. The finish layer does not determine the load-bearing capacity of the substrate.

By |2026-11-14T11:59:37+01:002023-11-20|Technology and applications|Comments Off on Fixing sandwich panels to masonry: how to provide adequate support

Roofing options after removing old asbestos cement sheets

Begin by establishing whether the old sheets actually contain asbestos, rather than judging them by colour and shape. If documents are missing, agree the identification method with the relevant authority and a contractor; do not take samples by breaking or drilling yourself. At the same time, assess the condition of the roof structure and the geometry of the slopes, since some problems only become visible once the sheets are removed. The choice of new covering — trapezoidal sheet or metal tile — depends on pitch, structure and building function. Also plan the safe removal of the old material and check with the municipality whether asbestos support covers only dismantling, transport and disposal.

By |2026-11-14T18:54:50+01:002023-11-19|Technology and applications|Comments Off on Roofing options after removing old asbestos cement sheets

Specifying left- and right-hand verge flashings on a roof drawing

The term left verge flashing is often ambiguous. It depends on which side we view the roof from and how we read the cross-section. When ordering, it is better to rely on a sketch than on the name alone. Verge flashings should be assigned to specific edges and their visible side marked. This is particularly useful for asymmetric elements, multiple roof slopes and different wall heights. On the building plan, it is worth marking the entrance side or another easily recognisable orientation. Then the individual gables and edges are marked. The person preparing the flashings should read the sketch in the same way as the installer. This helps avoid reversing the order.

By |2026-11-15T02:36:30+01:002023-11-13|Technology and applications|Comments Off on Specifying left- and right-hand verge flashings on a roof drawing

Sheet thickness for fence pickets. How to read the figures without oversimplifying?

Sheet thickness is an important parameter of a picket, but on its own it does not describe the quality of the fence. In offers for actual products, values such as 0.45 mm, 0.50 mm and a range of 0.5–0.6 mm appear, among others. This does not mean there is a single standard common to all models. Before comparing, it is necessary to establish what the number refers to and what conditions accompany it. Metal pickets are assessed together with the cross-section, length, material grade and method of fixing. The term 'sheet thickness' is sometimes used as shorthand. It is worth confirming whether the documentation refers to a specific thickness of the steel substrate or to a differently defined dimension of the product. Tolerances are also important. A more precise meaning should not be added to a number from a commercial description on one's own. The basis should be the data of the specific picket and the material from which it is made.

By |2026-11-15T17:18:33+01:002023-11-12|Technology and applications|Comments Off on Sheet thickness for fence pickets. How to read the figures without oversimplifying?

How to choose a roof colour that works with the façade

First establish which elements of the house will remain unchanged, and match the roof colour to them. During renovation, brick, stone, windows or fencing may outlast more than one coat of paint, so they set the palette. Also check gloss, texture and the sheet profile, as well as local requirements for the building's appearance. Before ordering, view a sample in daylight and at an angle close to the roof pitch. Make the final decision after comparing all permanent elements, not just a catalogue swatch.

By |2026-11-14T22:29:26+01:002023-11-11|Technology and applications|Comments Off on How to choose a roof colour that works with the façade

Will a mineral wool panel soundproof the hall, and how do you read its acoustic parameters?

A mineral wool core does not mean that every panel absorbs noise well inside the room. A panel with full steel facings can limit sound transmission while reflecting it back into the room. First you need to establish the problem: noise outside, between rooms or reverberation in the hall. Each requires a different approach. Insulation describes limiting the passage of sound through a partition. Absorption concerns the energy that does not return to the room as a reflection. These are different properties. Material hidden behind full steel sheet does not behave the same as an exposed or suitably protected absorbent layer.

By |2026-11-14T09:33:38+01:002023-10-29|Technology and applications|Comments Off on Will a mineral wool panel soundproof the hall, and how do you read its acoustic parameters?

Preparing your roof for snow, frost and winter weather

Winter roof preparation begins with deciding who will assess the need for snow removal and how it will be carried out, not with cleaning the gutters alone. Before the frost, repair loose flashings, damaged connections and active leaks before the weather makes access difficult. Also check the places where installation work was previously done, because openings left behind may only reveal a problem during lying snow and thaw. There is no single safe snow depth for all roofs – construction, weather conditions and actual load determine it.

By |2026-11-15T02:35:15+01:002023-10-28|Technology and applications|Comments Off on Preparing your roof for snow, frost and winter weather

Checking that flashings in one delivery match in material and colour

With a large order, flashings often come from several batches or arrive on site at different times. It is then easy to mix up the material, the surface finish or the colour side. One clear schedule limits the problem. It should describe each group of elements, from ridge caps to starter profiles. A joint delivery makes sense when all parts are easily identifiable and correspond to the approved specification. Ridge caps, barge flashings, gutter aprons and chimney flashings should be listed in separate rows. For each, add the cross-section, length and number of pieces. Starter profiles and other plinth elements should also be separated. This allows quantities to be checked without mixing the functions of similar profiles.

By |2026-11-15T02:36:48+01:002023-10-27|Technology and applications|Comments Off on Checking that flashings in one delivery match in material and colour

Why the cheapest covering can still mean a costly roof

What matters is whether you are comparing the cost of a complete roof, not just the price of a sheet. Check the coverage area, the type of coating and the scope of the offer, because a unit price without these details can be misleading. Also include accessories, transport, cutting and installation conditions, which may reverse an apparent saving. On a complex roof, flashings and accessories can account for a significant share, so it is worth comparing offers for your own project. Leave the final choice to the designer, who will assess whether the cheaper variant meets the required parameters.

By |2026-11-14T18:54:11+01:002023-10-24|Technology and applications|Comments Off on Why the cheapest covering can still mean a costly roof

Flat roof coverings: how to choose the right build-up

The choice of flat roof covering depends primarily on the geometry of the falls and the layout of the drains, not on the waterproofing material alone. Before laying the layers, check whether the design provides for the water flow path, substrate deflections and levels at parapets and service penetrations. Only then should the structural steel deck, PIR insulation and bitumen felt or membrane be selected as one system. A sandwich panel requires its own minimum slope, so it cannot replace an arbitrarily level assembly.

By |2026-11-14T18:52:57+01:002023-10-19|Technology and applications|Comments Off on Flat roof coverings: how to choose the right build-up
Back to top