What do 100 metres of sheet metal cost? Linear metres versus square metres

The question about 100 metres of steel sheet requires clarification of the unit. One hundred linear metres is the sum of the lengths of the sheets, while one hundred square metres is the area. The result also depends on the overall width or coverage width. These figures must be established before comparing prices. Otherwise, two similar amounts may refer to different quantities of material. A linear metre means a length of 1 m at a specified width. Twenty sheets of 5 m each give 100 linear metres. This does not yet indicate what area will be covered. The effective width of the specific profile is needed, along with information on any longitudinal joints.

By |2026-11-14T12:00:46+01:002023-10-03|Technology and applications|Comments Off on What do 100 metres of sheet metal cost? Linear metres versus square metres

How often should a roof be inspected and what maintenance does it need?

Start with the covering instructions and the way the roof is used, because these set a realistic inspection plan. Check above all the drainage, fixings, flashings and sheet surface, rather than mechanically repeating annual painting or tightening every screw. A roof under trees needs different attention from an exposed slope, so link dates to leaf removal and preparing drainage for the rainy season. After strong wind or hail, do not wait for the scheduled inspection. Also decide who will assess the slope after another team has worked there.

By |2026-11-14T18:56:11+01:002023-09-30|Technology and applications|Comments Off on How often should a roof be inspected and what maintenance does it need?

Timber connectors: common types and where they are used

The choice of a carpentry connector is determined by the whole node, not by the shape of the fitting alone. Before buying, check what loads it is to transfer, what the geometry of the components is and in what environment the connection will work. The specified nails, screws or anchors and the installation pattern also matter. An angle bracket, beam hanger or post base may serve different functions, and a similar appearance does not guarantee interchangeability. The documentation gives parameters for a specific arrangement, so it is worth knowing the connection diagram and the conditions for which they were determined.

By |2026-11-14T22:27:00+01:002023-09-24|Technology and applications|Comments Off on Timber connectors: common types and where they are used

How the profile of cut-to-length and modular roof sheets affects the finished roof

The appearance of tile-effect metal roofing depends mainly on the shape of the wave, the height of the transverse pressing and the rhythm of the divisions. The method of delivery in long sheets or small panels is a separate feature. Cut and modular coverings can suit both a calm, traditional building form and a simple modern house. It is best to assess a larger fragment of the covering in daylight, from a similar distance as the finished roof. The profile has a division along the roof slope and a division across the sheet. The waves run lengthwise, and the transverse rhythm is formed by the steps of the pressing. The height of the wave itself need not equal the total height of the finished panel. When comparing technical data sheets, the drawing must be checked.

By |2026-11-14T15:40:57+01:002023-09-23|Technology and applications|Comments Off on How the profile of cut-to-length and modular roof sheets affects the finished roof

How to choose a durable external window sill

Follow the water from the glazing, down the frame and across the sill when choosing an external window sill. A suitable outward fall, a drip edge clear of the façade and a sound junction with the window matter more to durability than the colour or finish. Select the coating once these details have been settled. On a refurbishment, lift the old sill and inspect what supported it. An uneven or poorly formed base may let water reach the wall long before a stain appears on the visible surface.

By |2026-11-14T22:28:41+01:002023-09-21|Technology and applications|Comments Off on How to choose a durable external window sill

BauderPIR FA-TE in terrace renovation with a low threshold

After the terrace surface has been removed, an uneven substrate and limited height at the doors are revealed. FA-TE should not be ordered solely on the basis of the thickness of the old material. The cross-section must be reconstructed together with the drainage. Only then can it be assessed which elements can remain and which need to be replaced. In a renovation, the scope described as insulating the terrace above a room requires an investigation of the old layers. The first difficult point to inspect is the threshold of the terrace doors and the nearby drain. It is not advisable to determine the thickness of BauderPIR FA-TE solely on the basis of an old drawing. The measurement should cover the distance between the substrate and the permissible surface level, taking into account changes made during earlier works.

By |2026-11-16T00:11:18+01:002023-09-18|Technology and applications|Comments Off on BauderPIR FA-TE in terrace renovation with a low threshold

What is a roofing underlay membrane and which properties matter?

A roofing membrane is a layer under the covering that protects against water and allows water vapour to escape. When selecting its parameters, check above all the product's intended use, diffusion resistance Sd, waterproofness and mechanical strength. Grammage alone is not enough for assessment. The key decision variable is compatibility with the temperature under the covering, the type of substrate and the planned installation time. Remember that the membrane does not replace the metal sheet or the internal airtight layer, and its strips and joints must form a continuous layer.

By |2026-11-14T22:28:58+01:002023-09-16|Technology and applications|Comments Off on What is a roofing underlay membrane and which properties matter?

Which roof covering suits your house?

Choose the covering to suit the roof pitch, the building structure and the way the building is used. Tile-effect metal roofing, trapezoidal steel sheet and insulated sandwich panels serve different functions. What matters is the cost of the whole roof build-up, as well as appearance, acoustics and the possibility of repair. Colour or the price of a single sheet is not enough. First check the design requirements, then compare the solutions approved for the given roof slope. Start with the pitch and dimensions of the slope. Every product has its own range of application. Tile-effect metal roofings come with different minimum pitches, so the parameter of one model does not apply to the whole group. At a low pitch, the laps, flashings and the method of water drainage become particularly important. The product data sheet and the installation instructions must be consistent with the design.

By |2026-11-14T15:39:38+01:002023-09-12|Technology and applications|Comments Off on Which roof covering suits your house?

Is metal picket fencing right for your property?

Metal pickets work well if you want a tidy fence with adjustable gaps and colour. Rather than generic claims of low maintenance, it is better to establish what role each part of the plot should play: the front, the area by the terrace and the rear garden may need different degrees of screening. Gaps change the view from both sides, and the density of the infill affects wind load. Before choosing, ask for a sample panel or a drawing of the layout to assess privacy and how it looks from the garden side.

By |2026-11-14T18:56:37+01:002023-09-11|Technology and applications|Comments Off on Is metal picket fencing right for your property?

What is a coated fence picket made of? Steel, galvanising and a colour coating

The colour of a fence picket is only the most visible part of the material. Beneath it lie the steel and the surface protection system. Each layer has its own job. Metal pickets that look alike therefore do not have to share identical parameters. The choice is best based on a specific material description rather than on the shade alone. The rear face and the conditions in which the fence will be used also matter. The coating is a protection system, not just decoration. Sheet-metal pickets are made from thin material profiled to a specific shape. The steel grade and thickness work together with the geometry of the cross-section. These determine how the element behaves once fixed. A coloured surface does not replace suitable material or proper supports. Rigidity should therefore not be judged by the name of the coating alone.

By |2026-11-15T17:18:36+01:002023-09-09|Technology and applications|Comments Off on What is a coated fence picket made of? Steel, galvanising and a colour coating
Back to top