Planning a durable patio roof

Start by deciding how much of the terrace should stay dry. Covering a strip along the house takes a different arrangement of supports from sheltering the full terrace. Measure the height available at the wall and at the outside edge, allowing space for the structure and roof fall. T18 or T35 profiled sheets and insulated roof panels each need a support layout, a drainage route and a suitable wall junction. Check the design for wind, snow and anchorage, and decide how water will leave the roof and how its underside should look before ordering.

By |2026-11-14T22:26:46+01:002023-09-06|Technology and applications|Comments Off on Planning a durable patio roof

How to inspect a panel roof when extending an old building?

A panel roof can be a solution for an extension if it suits the structure and the available height. The junction with the old building is often the most difficult part. The support, water drainage and conditions at the higher wall must be checked. The low weight of the panel alone does not determine suitability. An extension requires assessment of both parts together. Check the condition of the masonry, foundations and elements to which the extension is to be connected. Cracks, moisture and previous alterations may be relevant. Render does not show the full construction of the wall. If you plan to transfer loads onto it, a survey of the substrate and a proper design are required.

By |2026-11-14T12:01:24+01:002023-09-03|Technology and applications|Comments Off on How to inspect a panel roof when extending an old building?

Mono-pitch roofs: structure, advantages and limitations

A mono-pitch roof has a single slope and directs water in a chosen direction. Before deciding to use one, check above all whether you can provide a continuous load path from the roof slope through the rafters, purlins, walls and columns down to the foundations. It is this path, not the simple roof line itself, that determines the choice of structure and covering. It is also worth thinking through the top edge detail and water drainage in advance, as these details often decide the durability of the system.

By |2026-11-14T18:56:32+01:002023-08-23|Technology and applications|Comments Off on Mono-pitch roofs: structure, advantages and limitations

How long does trapezoidal steel roofing last?

There is no single number of years that applies to every trapezoidal steel sheet. Durability depends on the steel, the coatings, the environment, the installation and subsequent inspections. T18 and T35 describe the profile, not the expected service life. It is worth comparing the documentation for the specific product and the warranty conditions. Well-executed details and prompt repair of minor damage help to make the most of the material's potential. The steel sheet is protected by layers matched to the specific product. The metallic coating protects the steel, while the organic layer provides additional protection and determines the appearance. Their parameters must be read together. The colour name alone says nothing about resistance to corrosion or radiation. Two sheets of identical shade may have different coatings and conditions of use.

By |2026-11-14T15:40:18+01:002023-08-15|Technology and applications|Comments Off on How long does trapezoidal steel roofing last?

What is a glass-fibre facing in a sandwich panel?

In a sandwich panel, glass fibre can reinforce the inner resin facing. This does not mean a mineral wool core or a translucent rooflight. Such a panel is sometimes used in roofs of agricultural buildings. When selecting, the chemical conditions, cleaning, load-bearing capacity and the method of protecting the joints must be checked. An example solution has a profiled steel facing on the outside, a PUR or PIR core and a composite facing on the inside. The composite consists of polyester resin reinforced with glass fibre. Each of these parts has a different function and its own properties.

By |2026-11-14T09:33:56+01:002023-08-09|Technology and applications|Comments Off on What is a glass-fibre facing in a sandwich panel?

What steel thickness should you choose for trapezoidal sheet on a specific roof?

Sheet thickness must be selected together with the profile, support spacing and roof load. There is no single figure suitable for all roof slopes. Also, a higher trapezoidal profile does not give unlimited freedom. For comparison, the data for the specific section and the thickness of the steel substrate are needed, distinguished from the complete coating system. Establish how thickness is stated in the product specification. The steel substrate and protective layers are not the same thing. Comparing a total measurement with a value relating to the steel can lead to error. A clear description of the variant and its tolerances is needed.

By |2026-11-14T12:00:33+01:002023-07-30|Technology and applications|Comments Off on What steel thickness should you choose for trapezoidal sheet on a specific roof?

Thin PIR insulation in renovation: calculating its actual benefit

In an old building, the parameters of the layers that are left in place are not always known. When adding PIR boards, the data for the new product must be kept separate from the assumptions about the existing building component. A low lambda value helps to reduce the thickness required. It does not, however, replace a survey of the condition of the substrate and the old insulation. Pay attention to the decimal notation. The value 0.022 is ten times smaller than 0.22. An error of one zero completely changes the result of the calculation. The unit and the inequality sign also matter. Data copied from a shop description should be checked against the product data sheet and declaration. The value from the data sheet of a new board is relatively easy to verify.

By |2026-11-16T00:09:34+01:002023-07-23|Technology and applications|Comments Off on Thin PIR insulation in renovation: calculating its actual benefit

How do you convert the price per 1 m² of trapezoidal steel sheet into the actual cost of the roof covering?

The price per 1 m² of trapezoidal steel sheet may refer to different bases of calculation. A cheaper rate for the total area does not necessarily mean cheaper covering. The profile, steel thickness and coating also matter. To assess the cost, you need to combine the sheet description with the layout of your own roof slope. Only then is it worth comparing discounts. The total area results from the full width of the sheet. The effective area describes the covering after the intended side lap. Both methods may appear in quotes, so the unit must be clear. You should not compare the figures alone before checking this note.

By |2026-11-14T12:00:48+01:002023-07-21|Technology and applications|Comments Off on How do you convert the price per 1 m² of trapezoidal steel sheet into the actual cost of the roof covering?

PIR or XPS for a flat roof: how to decide based on the layer build-up?

On a flat roof, the layer build-up is chosen first, and only then the insulation. PIR placed beneath the waterproof covering performs differently from XPS in an inverted roof. Moisture, load and the method of fixing all matter. A lower lambda alone does not confirm that the material is suitable as a substitute in an existing solution. In a classic roof, the insulation sits beneath the waterproof layer. In an inverted roof, the thermal insulation lies above the waterproofing. That is the fundamental difference in service conditions. A material in the upper position must be suitable for contact with water and for the intended method of draining precipitation.

By |2026-11-14T09:33:52+01:002023-07-20|Technology and applications|Comments Off on PIR or XPS for a flat roof: how to decide based on the layer build-up?

PIR when replacing the roof covering: insulating without losing loft space

Replacing the roof covering is an opportunity to insulate the roof slopes from the outside. PIR boards above the rafters can limit intervention in finished rooms. Before starting, the condition of the timber, the heights of the layers and the way the new roof connects to the existing façade must be checked. PIR boards laid above the rafters form a layer that also covers the wooden structural elements. This makes it possible to reduce their contribution to heat flow through the roof. The exposed structure allows areas previously inaccessible to be assessed. The new insulation should be placed on a prepared assembly with a confirmed technical condition. After removing the covering, the timber and the locations of earlier leaks should be inspected. The new layer should not conceal sections requiring structural repair.

By |2026-11-16T00:09:50+01:002023-07-17|Technology and applications|Comments Off on PIR when replacing the roof covering: insulating without losing loft space
Back to top