Can you walk on an insulated panel roof during an inspection?

Do not assume an insulated panel roof is safe to walk on. Before an inspection, establish an access route and suitable protection. Ideally, plan both when choosing the roof covering, particularly if equipment on the roof will need servicing. A foot places a concentrated load on a small area. The top facing can deform locally even when the panel as a whole safely carries a distributed load. A snow load table alone therefore cannot establish that the roof is safe to walk on. The facings, core, supports and position of the load relative to the ribs and supports all matter. No single rule for foot placement applies to every profile.

By |2026-11-14T15:38:32+01:002022-12-29|Technology and applications|Comments Off on Can you walk on an insulated panel roof during an inspection?

Roof rafters: dimensions, types and what affects the price

The cross-section of a rafter is not determined by the roof covering alone, but by a set of structural parameters. Check the span between supports, spacing, timber class, support arrangement and loads — only these allow the beam's behaviour to be assessed. The length from eaves to ridge alone does not describe its performance, especially with intermediate support. When ordering, give the length from the documentation and the number of pieces; a dimension from a handbook does not replace a design for a specific house. Compare offers using the same material specification and scope of processing.

By |2026-11-14T22:26:40+01:002022-12-24|Technology and applications|Comments Off on Roof rafters: dimensions, types and what affects the price

Single-sided and double-sided fence slats. Two different decisions hidden in one word

The word "double-sided" can describe either the sheet surface or the way the slats are arranged. These are two different issues. A slat with a decorative colour on both sides can still form a single row. Conversely, two rows can be built from different finish variants if the system allows it. When talking about a fence, it is therefore worth using full descriptions. That way the metal slats will arrive in the ordered version, and the expected degree of screening will follow from the actual arrangement. A decoratively double-sided variant has a finish intended to be viewed from both sides. However, its exact description must be established. Do both surfaces have the same colour? Do the gloss and texture match? Is the woodgrain decor also present on the back? The word "coated" alone does not answer all these questions. The sheet may be protected on both sides yet look different on the front and the back.

By |2026-11-15T17:18:38+01:002022-12-19|Technology and applications|Comments Off on Single-sided and double-sided fence slats. Two different decisions hidden in one word

Choosing panels for cattle sheds, poultry houses and pig buildings

In a livestock building, the envelope works under different conditions than in a dry warehouse. Humidity, chemical compounds and regular cleaning matter. The surfaces, seals and fixings must be selected. The core thickness is important but does not determine the durability of the entire roof and walls. State the building's purpose, the temperature and humidity conditions and the ventilation method. Also describe the agents used during washing and disinfection. A cattle shed, poultry house and piggery do not have to have identical operating conditions. A general phrase 'agricultural use' is not enough.

By |2026-11-14T11:58:33+01:002022-11-29|Technology and applications|Comments Off on Choosing panels for cattle sheds, poultry houses and pig buildings

What to do when you find a roof leak

After noticing a leak, limit the damage inside and have the cause determined. The position of the stain on the ceiling need not lie directly beneath the damaged covering. Water can travel through the roof layers. Condensation can produce a similar symptom. Do not go onto a wet roof slope in search of a hole. An effective repair begins with a safe inspection and with distinguishing the source of the moisture. Move objects away from the drip point and restrict access to the affected part of the room. If water is near electrical installations, an assessment and safe handling by a competent person are required. Do not touch wet equipment. A sagging ceiling lining or plaster coming loose may pose an additional hazard to people beneath it.

By |2026-11-14T15:40:36+01:002022-11-28|Technology and applications|Comments Off on What to do when you find a roof leak

What does the Passive House standard require?

Whether a home meets the passive house standard depends on the energy balance of the whole building. Before selecting insulation boards, the designer assesses heat loss through the building envelope and its junctions, as well as the effects of windows and ventilation. Thicker roof insulation cannot seal an air leak around a window. The calculations therefore need to be backed up by good workmanship and an airtightness test on the completed envelope. When comparing designs, ask which floor area was used to calculate heating demand. This figure serves a different purpose from an individual household’s heating bill.

By |2026-11-14T22:27:25+01:002022-11-25|Technology and applications|Comments Off on What does the Passive House standard require?

Rooflights: where they work well and how to choose a system

A roof light is particularly useful in deep interiors where wall windows cannot bring daylight to the further zones. Before choosing a solution, establish the hours when the building is used and the type of activities carried out, then compare the light transmittance with the thermal insulation of the complete unit, not just the infill. In a roof made of sandwich panels, check that the profile and sealing details match. Bear in mind that the transparent surface is not intended for walking on.

By |2026-11-14T22:29:06+01:002022-11-21|Technology and applications|Comments Off on Rooflights: where they work well and how to choose a system

How do you calculate the required PIR thickness for a specific wall?

Choosing the PIR thickness can start with a simple thermal resistance calculation. First, you need to know the wall and the target U-value. Then you select a material with the right lambda and application. A calculator makes comparison easier, but it will not assess reveals, fixings and moisture on its own. These elements must be checked separately. Choose the U-value required in the project or adopted as the refurbishment target. Do not assume that the same thickness will be right for every house. A thin wall with high conductivity needs a different addition than a wall that already has an effective insulation layer.

By |2026-11-14T09:33:37+01:002022-11-16|Technology and applications|Comments Off on How do you calculate the required PIR thickness for a specific wall?

Measuring roof valley flashings and planning the joints

Ordering a roof valley requires measuring the line where the roof slopes meet and determining how it is to be finished. It is not enough to read the dimension from the building plan. The connections between successive sections must also be planned, and the cross-section matched to the drainage design. The valley flashing works in the area that collects water from the adjacent roof slopes. It is therefore worth preparing its schedule as carefully as the list of the covering itself. Every concave junction of roof slopes should be marked on the sketch. Individual valleys may differ in length, pitch and outlet position. They should not be entered under one item without distinction. Each section should be marked with a symbol corresponding to the roof drawing.

By |2026-11-15T02:36:49+01:002022-11-13|Technology and applications|Comments Off on Measuring roof valley flashings and planning the joints

Tile-effect metal roofing or clay tiles: which suits the house’s form and structure better?

When choosing between tile-effect metal roofing and clay tiles, it is worth starting with the specific roof slope. A simple roof and a roof with dormers will use material differently. The requirements for the structure, transport and flashings will also differ. The price per square metre does not show these differences. The best comparison comes from two quotes for the same roof. On a rectangular slope, long sheets of tile-effect metal roofing can be well matched to the slope length. With roof valleys, dormers and hips, the number of cuts increases. The cut-off piece is not always suitable for the other side of the roof. The direction of the profile or the position of the overlap can be an obstacle.

By |2026-11-14T09:23:49+01:002022-11-11|Technology and applications|Comments Off on Tile-effect metal roofing or clay tiles: which suits the house’s form and structure better?
Back to top