+48 500 409 109

How many ridge caps should you order for a metal roof?

The number of ridge caps is best established on a plan of all ridges and then verified by measurement. Dividing a single length by the product's nominal dimension gives only an approximate result. The order must account for joints, end pieces and differences between roof sections. It is also worth separating the quantity of sheet metal from the scope of installation. A well-described set reduces interruptions caused by the lack of one short element. On a simple roof, one section may be sufficient. With a complex roof shape, there are more ridges and not all have the same profile. The most convenient approach is to mark them on a sketch with consecutive symbols. For each, note the length, adjacent slopes and how both ends are finished.

By |2026-11-15T02:36:26+01:002024-08-02|Technology and applications|Comments Off on How many ridge caps should you order for a metal roof?
Read More

Clay tiles or tile-effect steel roofing: what to check before choosing

The choice between ceramic tiles and metal roofing depends on compliance with the design and the required roof pitch, not on the appearance of a sample. Check whether both coverings fall within the pitch limits given by the manufacturer for the specific product, since a single limit for the whole category does not exist. A shallow roof may need additional layers under the covering, which changes the cost and scope of work. Also analyse the load-bearing capacity of the roof structure, the fixing method, the full cost estimate including flashings, and local requirements for the building's appearance.

By |2026-11-14T22:28:20+01:002024-06-20|Technology and applications|Comments Off on Clay tiles or tile-effect steel roofing: what to check before choosing
Read More

How to refresh the appearance of a metal roof

Begin by establishing whether the deterioration in appearance affects the entire roof slope or only the areas around the chimney, branches or installations. A recurring run-off mark often points to the source of soiling higher up, so cleaning alone will give a short-lived effect if the cause is not corrected. Before commissioning a renovation, look at close-ups of different sections of the roof to distinguish deposits from damaged coating and to check tightness. Choose the scope of work after inspection, taking the type of steel finish into account.

By |2026-11-14T18:55:08+01:002024-06-15|Technology and applications|Comments Off on How to refresh the appearance of a metal roof
Read More

When are insulated sandwich panels a good fit for a roof?

A roof sandwich panel combines steel facings with an insulating core and, in a properly selected system, allows the roof to be closed and insulated quickly. When choosing, check above all whether the specific panel has been tested for loads, heat and fire and whether its joints, fixings and flashings match the design. The core type alone, such as PIR or mineral wool, does not determine the product's suitability, nor does its external appearance. Leave the decision on support spacing and sealing to the designer, as these depend on the system and the building conditions.

By |2026-11-15T02:34:34+01:002024-06-11|Technology and applications|Comments Off on When are insulated sandwich panels a good fit for a roof?
Read More

Roofing panels and sheets: what to check before choosing a covering

Before choosing panel or sheet roofing, first establish the roof pitch, the method of support and whether the building will be heated, and only then compare products. Check the coverage width, the minimum pitch for the specific product and all the layers beneath the covering. A trade name can be misleading: a panel may mean a small module of tile-effect sheeting, a long metal sheet or a sandwich panel, so state the full category, profile shape and intended roof build-up in your enquiry.

By |2026-11-14T22:27:44+01:002024-06-01|Technology and applications|Comments Off on Roofing panels and sheets: what to check before choosing a covering
Read More

Fibre cement roof ridge. Selection of fittings and ventilation

The ridge looks like a narrow strip at the top of the roof, but it combines several important functions. It covers the junction between the roof slopes, takes up water driven in by the wind and can provide an outlet for air from beneath the covering. Fibre cement sheets require a compatible set of fittings and fastenings here. Asbestos-free fibre cement does not form a complete roof without the correct termination. Choosing a ridge tile by colour alone overlooks the factors that determine tightness and moisture beneath the covering. The type of ridge element depends on the roof pitch and the way the two sides are joined. Some solutions have a defined adjustment range, others require the correct angle. This range is not, however, the permissible pitch of the covering itself.

By |2026-11-15T17:20:43+01:002024-05-17|Technology and applications|Comments Off on Fibre cement roof ridge. Selection of fittings and ventilation
Read More

Metal roofing and energy use: what difference does the insulation make?

The metal sheet alone does not determine energy use – the whole roof assembly matters, not just its outer layer. Before renovating, check whether the insulation sits in a separate layer or forms the core of a sandwich panel, as these are different systems. Compare the existing thermal resistance with the designed one, including thermal bridges and joint airtightness. Choosing a material with lower lambda may reduce insulation thickness, but it does not guarantee specific savings. Leave the scope of works to the designer.

By |2026-11-14T22:25:57+01:002024-04-29|Technology and applications|Comments Off on Metal roofing and energy use: what difference does the insulation make?
Read More

Tile-effect metal sheets or concrete roof tiles? Comparing cost and weight

Choose the covering based on the permissible load on the roof structure and the actual scope of work, not just the price per metre of material. Check whether the structure can carry the weight of concrete tiles, especially during renovation, where existing sheet metal does not guarantee a reserve. Compare the mass of the finished covering surface, the fixing method, waste and accessories. In the contractor's offer, look at demolition, roof structure repairs, battens, flashings and transport. In strong winds, the complete fixing system matters, not weight alone. Leave the final choice to the designer, as roof geometry and timber condition are decisive.

By |2026-11-14T18:54:49+01:002024-04-26|Technology and applications|Comments Off on Tile-effect metal sheets or concrete roof tiles? Comparing cost and weight
Read More

How will the house change after replacing roof tiles with a photovoltaic roof?

Replacing roof tiles with an integrated photovoltaic covering clearly changes the character of the house. Instead of a fine, undulating pattern, a calmer surface with longitudinal divisions appears. The cells are part of this composition, and passive fields complete the roof slope. Such a renovation can refresh an older building without adding separate panels on a mounting frame. However, it is worth refining the proportions, the colour of the flashings and the relationship between the roof and the façade beforehand. Roof tiles create a rhythm of many small elements. A steel roof integrated with cells has a different pattern and usually emphasises the direction of the roof slope more strongly. As a result, the house may look calmer and more contemporary. This is not automatically a better effect, but a specific change that is worth assessing against the whole building form.

By |2026-11-15T17:19:32+01:002024-04-22|Technology and applications|Comments Off on How will the house change after replacing roof tiles with a photovoltaic roof?
Read More

Cut-to-length sheets or modular metal roof tiles for your roof?

The format of the roofing sheet should be matched to the specific roof, not to a general rule. First check whether the slopes are simple and even, or rather full of valleys, dormers and short sections, as this determines the number of cuts and joints. The second step is delivery conditions: a long sheet needs space for unloading and lifting onto the roof, while modules are easier to distribute and store. Compare the cutting plan, transport, accessories and labour for the whole roof, not the price per piece.

By |2026-11-15T02:34:26+01:002024-04-17|Technology and applications|Comments Off on Cut-to-length sheets or modular metal roof tiles for your roof?
Read More
Back to top