About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Will 40 mm second-quality insulated roof panels suit your roof?

For a 40 mm second-grade roof panel, first check the intended use, the condition of the joints and the usable lengths. A thin core does not mean that any support spacing is acceptable. A reduced price does not remove the requirements for slope and tightness. Buying makes sense when the specific components suit the project and the extent of their defects is known. In roof panels, the nominal core thickness and the overall height may differ. The upper steel sheet has a profile that increases the external dimension of the component. Check the cross-section of the actual panel. Measuring at the top of the trapezoidal profile without knowing the designation can lead to an incorrect comparison of two offers.

By |2026-11-14T15:38:37+01:002023-05-03|Technology and applications|Comments Off on Will 40 mm second-quality insulated roof panels suit your roof?

Choosing between vertical and horizontal façade panels

The panel direction changes more than just the façade pattern. It affects the arrangement of supports, the lengths of elements and the locations of joints. Vertical strips may suit one building form, and horizontal strips another. The choice must be verified for the specific system. It is best to start with the openings and the wall geometry before the framing is ordered. This should not be assumed without confirmation. Many wall families allow both layouts, but they have specific details and conditions. The direction of the interlock and the method of water drainage must match the instructions. Rotating the product is not merely a change of appearance.

By |2026-11-14T12:01:07+01:002023-04-27|Technology and applications|Comments Off on Choosing between vertical and horizontal façade panels

Planning lengths and corners for made-to-measure parapet copings

With a parapet, the building perimeter is not the only thing that matters. Copings must fit the actual wall width, the position of the layers and the planned drainage. The order must include straight sections, corners and changes in height. A complete set prepared in this way is easier to install and to accept. It also avoids a situation where the straight strips are ready but one end piece is missing, stopping the whole parapet from being closed. Measurement should cover all layers that will sit under the flashing. The dimension of the wall or structure alone is not enough. The final finish on both sides must be taken into account. If the façade is not yet finished, its actual thickness needs to be agreed.

By |2026-11-15T02:37:02+01:002023-04-24|Technology and applications|Comments Off on Planning lengths and corners for made-to-measure parapet copings

How to prepare a metal roof for repainting

Painting a metal roof makes sense only when the steel and its fixings can accept a new coating. First establish whether surface deposits, faded paint or perforation of the sheet rule out renovation. The key decision is matching the system to the existing finish and its adhesion, in line with the supplier's documentation. Also check the gutters, eaves, areas around the chimney and service penetrations, plus the underside of the covering where accessible. The scope of repairs and substrate preparation should follow this assessment, not the desired colour.

By |2026-11-14T18:55:13+01:002023-04-21|Technology and applications|Comments Off on How to prepare a metal roof for repainting

What a pronounced stepped profile changes in modular tile-effect roofing

The distinct appearance of modular metal roofing tiles comes primarily from the profile geometry, not from wave height alone. When choosing, check the effective cover width, the number of modules per sheet and the permitted roof pitch — these parameters determine the roof layout and the product's suitability. A high profile does not replace correct support or fixing, so compare a sample with the technical drawing rather than relying on a photograph alone. Also remember that the same profile looks different on a cloudy day and in strong sunlight.

By |2026-11-14T18:56:34+01:002023-04-19|Technology and applications|Comments Off on What a pronounced stepped profile changes in modular tile-effect roofing

Which materials make a lightweight roof covering?

A lightweight roof covering is one whose mass does not excessively burden the roof structure, and the materials mentioned include trapezoidal sheet and metal roof tiles. Before comparing, check whether the stated mass refers to a sheet, a square metre of total area or of covering, and whether the overlap is included in the balance. Separately verify loads from snow, wind and equipment. The decisive factor is the weight of the entire roof system, not the sheet alone, so leave the choice to the designer.

By |2026-11-14T22:28:02+01:002023-04-09|Technology and applications|Comments Off on Which materials make a lightweight roof covering?

What sets insulated sandwich roof panels apart from other roof coverings?

A sandwich roof panel is a finished element in which the facings and core work together to carry loads, so its suitability depends on conformity with the design rather than the promise of quick installation alone. Before choosing, check that the load-bearing, thermal and fire parameters meet the building's requirements and that support and sealing for openings are provided. Compare the complete panel, not the core alone, and consider the slope and junction details. Leave the application decision to the designer, because the whole roof assembly determines suitability.

By |2026-11-14T18:52:56+01:002023-04-08|Technology and applications|Comments Off on What sets insulated sandwich roof panels apart from other roof coverings?

How should you cut insulated wall panels to preserve the edges and coating?

It is best to order panels in the required length. When on-site cutting is necessary, use a tool that complies with the panel guidelines and limit heating of the sheet. Support and prompt removal of swarf are equally important. A well-executed cut should fit the planned flashing and edge support. Check the dimension after installation, not just the distance between two visible elements. Clearances, space for flashings and the required bearing may be needed. For a roof panel, also allow for the direction of fall and the eaves or lap detail. Do not cut the whole batch according to the first unconfirmed piece.

By |2026-11-14T09:33:49+01:002023-03-18|Technology and applications|Comments Off on How should you cut insulated wall panels to preserve the edges and coating?

How do I choose T14 trapezoidal steel sheet for roof dimensions and support spacing?

T14 trapezoidal steel sheet has a low profile, but choosing it does not end with the number in the name. You need to check the cover width, steel thickness and support conditions. On a small roof, the width of the last strip also matters. A well-drawn layout reduces cuts and lets you determine the flashings at both edges of the roof slope in advance. The designation T14 refers to a profile height of approximately 14 mm. It does not define a single width or a single load capacity. Sheets with the same number in the name may have different rib spacing and different side edges. So compare full cross-sections, not just the symbol.

By |2026-11-14T09:23:43+01:002023-03-16|Technology and applications|Comments Off on How do I choose T14 trapezoidal steel sheet for roof dimensions and support spacing?

How to choose between tile-effect metal roofing and trapezoidal steel sheet for a house roof?

Tile-effect metal roofing and trapezoidal steel sheet are both made from profiled sheet metal, but they organise the appearance of the house differently. The first creates a rhythm of transverse steps. The second runs clear lines from the eaves up the roof slope. The choice should also be determined by pitch, layout and structural requirements. The label 'for a house' or 'for a hall' alone explains little. On a low building the roof takes up a large part of the visible volume. Tile-effect metal roofing gives a division close to the arrangement of roof tiles. Trapezoidal steel sheet creates a calmer rhythm in one direction. Both solutions can suit a house if their scale harmonises with the façade and joinery.

By |2026-11-14T09:31:18+01:002023-03-16|Technology and applications|Comments Off on How to choose between tile-effect metal roofing and trapezoidal steel sheet for a house roof?
Back to top