Clay tiles or tile-effect steel roofing: what to check before choosing

The choice between ceramic tiles and metal roofing depends on compliance with the design and the required roof pitch, not on the appearance of a sample. Check whether both coverings fall within the pitch limits given by the manufacturer for the specific product, since a single limit for the whole category does not exist. A shallow roof may need additional layers under the covering, which changes the cost and scope of work. Also analyse the load-bearing capacity of the roof structure, the fixing method, the full cost estimate including flashings, and local requirements for the building's appearance.

By |2026-11-14T22:28:20+01:002024-06-20|Technology and applications|Comments Off on Clay tiles or tile-effect steel roofing: what to check before choosing

How to refresh the appearance of a metal roof

Begin by establishing whether the deterioration in appearance affects the entire roof slope or only the areas around the chimney, branches or installations. A recurring run-off mark often points to the source of soiling higher up, so cleaning alone will give a short-lived effect if the cause is not corrected. Before commissioning a renovation, look at close-ups of different sections of the roof to distinguish deposits from damaged coating and to check tightness. Choose the scope of work after inspection, taking the type of steel finish into account.

By |2026-11-14T18:55:08+01:002024-06-15|Technology and applications|Comments Off on How to refresh the appearance of a metal roof

When are insulated sandwich panels a good fit for a roof?

A roof sandwich panel combines steel facings with an insulating core and, in a properly selected system, allows the roof to be closed and insulated quickly. When choosing, check above all whether the specific panel has been tested for loads, heat and fire and whether its joints, fixings and flashings match the design. The core type alone, such as PIR or mineral wool, does not determine the product's suitability, nor does its external appearance. Leave the decision on support spacing and sealing to the designer, as these depend on the system and the building conditions.

By |2026-11-15T02:34:34+01:002024-06-11|Technology and applications|Comments Off on When are insulated sandwich panels a good fit for a roof?

Designing modern façades with sheet metal and sandwich panels

The key to a modern building form is a disciplined division of surfaces, not the choice of sheet metal or sandwich panels alone. Readers should first check the proportions of the roof, walls and openings, and draw the layout of sheets and panels together with the joinery, because a regular material exposes every inconsistency, such as a narrow offcut at a corner. The role of each layer is equally decisive: roof covering, wall panel and separate insulation have different tasks, and their combination should reconcile appearance with drainage, thermal insulation and load-bearing capacity.

By |2026-11-14T18:54:15+01:002024-06-01|Technology and applications|Comments Off on Designing modern façades with sheet metal and sandwich panels

Roofing panels and sheets: what to check before choosing a covering

Before choosing panel or sheet roofing, first establish the roof pitch, the method of support and whether the building will be heated, and only then compare products. Check the coverage width, the minimum pitch for the specific product and all the layers beneath the covering. A trade name can be misleading: a panel may mean a small module of tile-effect sheeting, a long metal sheet or a sandwich panel, so state the full category, profile shape and intended roof build-up in your enquiry.

By |2026-11-14T22:27:44+01:002024-06-01|Technology and applications|Comments Off on Roofing panels and sheets: what to check before choosing a covering

How to plan and cost a sandwich panel garage

The cost of a panel garage depends on more than its floor area. You need to account for the walls, roof, door and structure. On a small plot, access and assembly space also matter. A good cost estimate starts with dimensions and how the garage will be used. Only then do you compare material prices. Start with the car, walkways and space for opening the doors. Add planned shelving and a work area. External dimensions are not usable dimensions. The structure, panels and flashings take up part of the space. Also check the entry height after allowing for the door mechanism.

By |2026-11-14T11:58:29+01:002024-06-01|Technology and applications|Comments Off on How to plan and cost a sandwich panel garage

What needs to be checked before choosing an insulated wall panel with 100 mm mineral wool?

A 100 mm panel with mineral wool can appear in many projects, but there is no single common set of parameters. Cores, facings and joints vary. Before purchase, it is worth checking the entire wall solution. Particularly important are the support spacing, openings and the thermal and fire requirements adopted for the building. In an example wall family, a 100 mm panel has a mass of approximately 19.8 kg/m² and a Uc of approximately 0.41 W/(m²·K). Another version of the same thickness may weigh approximately 17.8 kg/m² and have a Uc of approximately 0.40. The data must be linked to the exact facings and product construction.

By |2026-11-14T09:32:40+01:002024-05-31|Technology and applications|Comments Off on What needs to be checked before choosing an insulated wall panel with 100 mm mineral wool?

How do you convert EPS to PIR without confusing thickness with thermal performance?

A centimetre of EPS does not provide the same thermal resistance as a centimetre of any PIR board. The comparison must be based on the lambda value of the specific material. The whole wall build-up and its finish are then checked. A thinner layer may make the reveal detail easier to resolve, but the difference in thickness alone does not determine the choice. First read the lambda value of both products under consideration. Do not assume a single figure for all EPS or for the entire PIR group. Properties depend on the variant. A board with a metallised facing may have a different application and parameter from a board intended for plaster.

By |2026-11-14T09:33:32+01:002024-05-31|Technology and applications|Comments Off on How do you convert EPS to PIR without confusing thickness with thermal performance?

Renovating a flat roof with Eurothane Silver: when details need changing

Insulating a flat roof may require raising the flashings and adjusting the position of the outlets. Eurothane Silver should be selected after these constraints have been assessed. First, it must also be checked whether the old layers are dry and whether they can serve as a substrate for the new build-up. Recticel Eurothane Silver is a PIR board with multi-layer gas-tight foil on both sides and a printed grid. The current data sheet specifies it for flat roofs in a classic build-up. During the pre-renovation inspection, examine the classic flat roof for which mechanical fixing, bonding or ballasting is being considered. Eurothane Silver must be assigned to a specific mechanically fixed, bonded or ballasted system before the scope of demolition is determined and the old roof construction is prepared.

By |2026-11-16T00:10:45+01:002024-05-28|Technology and applications|Comments Off on Renovating a flat roof with Eurothane Silver: when details need changing

Choosing one supplier for sandwich panels and sheet metal

A large selection of material only helps if you can assemble your own building from it. With panels and sheets, matching dimensions, accessories and efficient delivery are important. The size of the warehouse does not answer all these questions. A supplier is worth assessing against a specific schedule, not just the number of offers. Start by dividing into walls, roof and flashings. For each group, enter the dimensions and required properties. For panels, the core, thickness and module are needed. For sheets, also the profile, steel thickness and cover width. Colour without the type of coating does not complete the material description.

By |2026-11-14T11:59:55+01:002024-05-25|Technology and applications|Comments Off on Choosing one supplier for sandwich panels and sheet metal
Back to top