Acoustic EPS and rigid EPS: what is the difference?

Acoustic polystyrene is intended to reduce impact sound in a properly constructed floating floor. It differs from hard EPS, which is selected primarily for load transfer. We explain the role of dynamic stiffness, compressibility and perimeter insulation, and the reasons why the material alone does not guarantee quiet. Footsteps, moving a chair and objects being dropped can set the floor structure vibrating. The resilient layer under the screed limits the transmission of part of these actions to the structure. It is precisely in such a system that a suitable acoustic EPS is used. Its action should not be equated with absorbing reverberation inside the room or with universally soundproofing every type of noise. Airborne sound, such as conversation, depends on other properties of the entire separating element and on flanking paths.

By |2026-11-16T04:51:30+01:002022-07-24|Technology and applications|Comments Off on Acoustic EPS and rigid EPS: what is the difference?

T18 or T35: how to choose trapezoidal steel sheet for a roof

The choice between T18 and T35 does not follow from the profile number alone but from the data for the specific roof. Before buying, compare the load tables, covering width, coating and slope requirements. Check whether the chosen variant is intended for roofing rather than cladding, and whether, when extending an old covering, the lap will match the existing sheet. Leave the final decision on profile, steel thickness and support spacing to the designer, because the number alone does not determine load capacity.

By |2026-11-14T22:28:07+01:002022-07-22|Technology and applications|Comments Off on T18 or T35: how to choose trapezoidal steel sheet for a roof

Making a loft with sloping ceilings comfortable to use

A floor plan tells you how much floor a loft contains. A section tells you where you can stand upright, open a wardrobe door or reach the window. Measure the headroom at several points as you move away from the low eaves wall. Mark any posts and collar ties, then allow for insulation and the finished lining under each slope. In a refurbishment, a survey made before the roof was insulated can give a misleading picture of the space a person or a piece of furniture will actually occupy.

By |2026-11-14T22:25:54+01:002022-07-19|Technology and applications|Comments Off on Making a loft with sloping ceilings comfortable to use

Choosing a roof covering for an industrial building

The choice of roofing for an industrial hall depends primarily on the building's purpose and the conditions inside it. Before comparing trapezoidal sheet, sandwich panels or a roof on structural decking, establish whether the hall will be heated, what humidity levels prevail and whether aggressive substances are present. Also check the purlin spacing, loads, and fire and acoustic requirements. For an unheated shelter, a suitably selected trapezoidal sheet may suffice, but in a hall with wet processes an anti-condensation layer alone will not solve the problem. Leave the final decision to the designer.

By |2026-11-14T18:54:35+01:002022-07-16|Technology and applications|Comments Off on Choosing a roof covering for an industrial building

Five roofing faults to look for before handover

The key decision before accepting a metal roof is whether the inspection will cover layers that will soon disappear beneath the covering. It is worth checking the geometry of the substrate, the batten spacing, the method of fixing, the condition of the coating, the continuity of ventilation and the routes for water drainage. Most problems stem from faults that are visible before work is completed, so photographs and stage-by-stage inspections offer more than a view of the finished slope from the ground. Documentation of the stages helps catch errors before correcting them becomes expensive.

By |2026-11-14T22:28:44+01:002022-07-14|Technology and applications|Comments Off on Five roofing faults to look for before handover

XPS on the plinth under render. Why does the board surface matter?

The plinth of a house must withstand rain, dirt and accidental impacts. If it is to be rendered, the insulation board becomes the substrate for the subsequent layers. XPS is then selected differently than for loosely laid floor insulation. Extruded polystyrene should have a surface suited to the intended finish. A smooth board with a good lambda value is not automatically the right substrate for mortar. What matters is the whole set of materials and the way it is installed. XPS can have a smooth surface layer created during production. It is useful in many applications, but adequate adhesion is needed when bonding and rendering. That is why rough, treated or structured boards are also available.

By |2026-11-16T04:50:26+01:002022-07-10|Technology and applications|Comments Off on XPS on the plinth under render. Why does the board surface matter?

Choosing a sandwich panel by application, size and price

The name Oborniki panel is commonly used for sandwich panels. It does not specify a single core, size or level of insulation. When buying, you therefore need to move from the general name to a specific variant. Price only makes sense alongside parameters, length and quantity. That way you can compare offers that correspond to the same task. A sandwich panel combines an insulating core with facings. In many solutions both facings are steel, but versions with a different internal finish also exist. The full construction must always be established. An insulating panel with a thin foil is not the same product as a steel panel.

By |2026-11-14T11:59:54+01:002022-07-06|Technology and applications|Comments Off on Choosing a sandwich panel by application, size and price

Flat roof renovation with termPIR WS: checking beneath the old membrane

Covering an old roof with another layer does not solve the problem of hidden moisture. Before installing termPIR WS, the condition of the existing materials must be assessed. Only then can it be determined what stays, what needs to be removed and where new details will be required. termPIR WS consists of a PIR core with a vapour-permeable glass fleece facing on both sides. This is a different surface from a vapour-tight aluminium laminate. During the pre-renovation inspection, check the surface of the flat roof where the board facing is to work together with the covering. The termPIR WS glass fleece must be matched to the layers and the fixing method of the chosen roof covering before the scope of demolition is determined and the old assembly is prepared.

By |2026-11-16T00:10:13+01:002022-07-03|Technology and applications|Comments Off on Flat roof renovation with termPIR WS: checking beneath the old membrane

Which measurements are needed for made-to-measure chimney flashings?

Chimney flashings are difficult to order from a single photo. You need the dimensions of the penetration, the roof pitch and information about the covering. Each side of the chimney may have a different role in draining water. That is why it is worth preparing the measurements as a simple set of drawings. This will make it easier to discuss with the contractor and to compare quotes that actually cover the same scope. The final solution must be consistent with the roof penetration design. The clearest way to describe the chimney is as the lower side, the upper side and the two lateral sides. This division relates to water runoff and reduces ambiguity. The term front can be misleading when one person is looking from the street and another from the ridge. The sketch should indicate the direction down the roof.

By |2026-11-15T02:36:46+01:002022-06-19|Technology and applications|Comments Off on Which measurements are needed for made-to-measure chimney flashings?

What does the reaction-to-fire class of an EPS board tell us?

The reaction-to-fire class describes the behaviour of a product under specified test conditions. For many EPS boards this is class E. It should not be confused with the classification of the finished ETICS, the fire resistance of the wall or the assessment of the roof. We explain these differences and show which documents to check before selecting the insulation and carrying out the works. Class E is a declaration of the reaction to fire of a specific product under specified conditions. It does not mean non-combustibility. EPS is an organic material and requires application in accordance with the design and the documentation. The data on the label must be read together with the scope of the classification. The symbol alone does not determine whether the board is suitable for every building and every building component.

By |2026-11-16T04:51:29+01:002022-06-07|Technology and applications|Comments Off on What does the reaction-to-fire class of an EPS board tell us?
Back to top