IDELCO α-therm SARKING boards when replacing a roof covering

IDELCO α-therm SARKING can be considered as thermal insulation above the rafters when replacing the roof covering while retaining the loft's interior finish. It is a PIR board with a multi-layer aluminium laminate on both faces and a tongue and groove on all four edges. The laminate must not be confused with a separate underlay membrane. A renovation requires an assessment of the old structure, the existing layers and the joints that will later become inaccessible. Below we discuss the continuity of the insulation, the change in the height of the roof slope and the selection of the complete cross-section. Retaining the interior does not exempt you from these inspections. When describing the material, it is worth using the exact PIR name: the terms “polyurethane boards” and “polyurethane foam” cover a broader group of products.

By |2026-11-16T04:44:37+01:002022-06-05|Technology and applications|Comments Off on IDELCO α-therm SARKING boards when replacing a roof covering

What are sheet metal flashings and where does a roof need them?

Flashings are there to carry water through places where an ordinary roofing sheet does not provide continuity — at the edge of a slope or against an obstacle such as a chimney. When planning, the first thing to check is whether the profile of the flashing directs the flow onto the next drainage surface, rather than merely covering the edge. Equally important is whether the detail works together with the layer beneath the covering and does not close off the required airflow. The shape depends on the specific location, so the colour of the sheet alone is not enough.

By |2026-11-14T18:55:07+01:002022-06-03|Technology and applications|Comments Off on What are sheet metal flashings and where does a roof need them?

XPS under a foundation slab. What should the structural engineer check?

A foundation slab may rest on a layer of thermal insulation if the design provides for this. In such an arrangement, XPS has a different task from a thin board bonded to a wall. It carries long-term actions and influences the deformation of the entire support. Extruded polystyrene must therefore be selected on the basis of calculations and the data for the specific product. The designation of a common compression class is not on its own an answer to the question of whether the material is suitable under a given house. Walls, columns and heavy items of equipment transmit forces at specific points. The foundation slab distributes them in accordance with its construction and support. XPS must be assessed within this actual arrangement.

By |2026-11-16T04:50:27+01:002022-06-01|Technology and applications|Comments Off on XPS under a foundation slab. What should the structural engineer check?

Support spacing for fibre cement. Why is it not determined by length alone?

A longer sheet does not mean the purlins can be spaced further apart. This is one of the more common mental shortcuts when pricing a roof. Fibre cement sheets work within a defined arrangement of supports and fixings. Their length must match the laps, but the permissible spacing also depends on the product's properties and the loads. Asbestos-free fibre cement is best chosen together with the design of the substructure. That way, saving on format does not weaken the roof slope. A support must carry the load from the sheet and provide the correct fixing position. It is not enough for it to be somewhere under the sheet. Its position must be tied to the edges, laps and rows of holes.

By |2026-11-15T17:20:24+01:002022-05-27|Technology and applications|Comments Off on Support spacing for fibre cement. Why is it not determined by length alone?

Thermano Roof when replacing a roof covering: planning additional insulation

Replacing the roof covering is an opportunity to improve the insulation, but it also reveals the condition of the old structure. Thermano Roof should be selected after that structure has been assessed. What matters are the eave levels, the junctions at the walls and the way the new layer build-up transfers loads. Thermano Roof is a rigid PIR board with a gas-tight multilayer aluminium facing on both sides. The manufacturer specifies it for, among other things, flat roofs and above-rafter insulation. During the pre-renovation inspection, check the pitched roof slope on which the insulation is to be placed above the timber rafters. The Thermano Roof layer above the rafters must be tied in with the terminations at the eaves and openings before the scope of demolition is determined and the old building envelope is prepared.

By |2026-11-16T00:10:27+01:002022-05-23|Technology and applications|Comments Off on Thermano Roof when replacing a roof covering: planning additional insulation

Checking cold-formed steel sections before accepting delivery

Receiving the material should not be limited to counting packages. It is important to establish whether the correct profiles have arrived and whether they have retained the required condition. Some discrepancies are easy to spot immediately. Others only become apparent when attempting installation. A checklist prepared in advance helps to separate these issues and gather the information needed to clarify a problem. The basis should be the final version of the schedule and drawings. An earlier quote may not cover subsequent changes. Item numbers, quantities and lengths should be checked. Variant markings are also important. Left and right parts can look very similar.

By |2026-11-15T17:18:19+01:002022-05-12|Technology and applications|Comments Off on Checking cold-formed steel sections before accepting delivery

Trapezoidal steel sheets for cladding and structural use: how their roles differ

Trapezoidal sheeting serves one of two functions in a building: protective or structural, and the choice between them depends on whether it is to carry loads between supports or merely close the partition against the weather. It is worth checking the documentation for the specific profile, because the name T18 or T35 alone does not determine its use. Differences in steel thickness and rib shape affect load capacity, but only the design establishes whether a given sheet may work as a load-bearing element. The selection decision is left to the designer.

By |2026-11-14T22:29:02+01:002022-05-10|Technology and applications|Comments Off on Trapezoidal steel sheets for cladding and structural use: how their roles differ

EFIGREEN ALU+ in renovation: assessing the substrate and new waterproofing

The renovation covers several small areas between existing installations. With ALU+, it is worth measuring each one separately and preparing a cutting plan. The assumption that a larger board will always reduce waste may not hold here. Narrow offcuts do not have to fit the next area. In a renovation, the scope described as insulating a roof slope broken up by numerous service penetrations requires an examination of the old layers. The first difficult spot to inspect is the narrow area between two installation bases. It is not worth determining the thickness of EFIGREEN ALU+ solely on the basis of an old drawing. The measurement should cover the width of the strip and the lengths available for laying full boards, taking into account changes made during earlier work.

By |2026-11-16T00:11:03+01:002022-05-06|Technology and applications|Comments Off on EFIGREEN ALU+ in renovation: assessing the substrate and new waterproofing

What accessories are needed for metal fence slats? From rails to screws

Metal fence slats are the visible part of a fence, but on their own they do not form a complete system. They need supports and connections that match their dimensions and layout. A single missing correct accessory can halt installation or lead to improvised modification. It is therefore worth preparing the list together with the choice of profile. Not every screw, connector and strip will fit a similarly looking slat. Compatibility is determined by the documentation for the specific solution and by the construction of the entire bay. In a typical vertical layout, the slats are fixed to rails or a frame. The rails connect to the posts, and these to the foundation. Each of these elements has its own role. Sheet metal slats do not replace structural reinforcement. The selection of accessories should therefore begin with a plan of the entire system, not with the colour of the screw head.

By |2026-11-15T17:18:22+01:002022-05-03|Technology and applications|Comments Off on What accessories are needed for metal fence slats? From rails to screws

When does a roof need repair and when does it need replacing?

The condition of the whole roof assembly and the cause of the fault, not the age of the covering, should determine whether to repair or replace. Before comparing costs, establish the water's path: it may travel along the membrane or flashing and appear far from the point of entry. Check whether the problem is limited and can be permanently removed, or whether it involves widespread corrosion, repeated leaks or damaged layers. Also distinguish a leak from condensation. A diagnosis from outside and from the accessible interior allows the scope of work to be matched to the actual cause.

By |2026-11-15T02:35:11+01:002022-04-28|Technology and applications|Comments Off on When does a roof need repair and when does it need replacing?
Back to top