How can T8 trapezoidal steel sheet be used on façades, soffits and light cladding?

T8 is a sheet with a low profile, usually associated with façades, soffits and cladding. It gives a subtle surface texture. However, it should not be selected on appearance alone. Thickness, coverage and support are important. On a small wall, it is worth planning the divisions at windows and the width of the edge sections in advance. The number refers to a profile height of approximately 8 mm. It does not describe the thickness of the steel core. An example variant has an overall width of 1220 mm and an effective width of 1156 mm. Other products with a similar name may differ in cross-section and coverage width.

By |2026-11-14T09:31:35+01:002022-01-20|Technology and applications|Comments Off on How can T8 trapezoidal steel sheet be used on façades, soffits and light cladding?

What to include on a drawing for a made-to-order flashing

An elaborate graphic design is not always needed to order a non-standard flashing. What is needed, however, is unambiguous data. A clear cross-section with dimensions and a material description is more useful than an attractive view without scale. It is worth preparing such a drawing in a consistent layout. It makes quoting, confirming bending feasibility and later acceptance of the components easier. The drawing should show the shape after bending. Each leg is given a dimension, and bends requiring a specific angle are described. No part should be left as more or less horizontal. The person preparing production must know what result is to be achieved.

By |2026-11-15T02:37:03+01:002022-01-20|Technology and applications|Comments Off on What to include on a drawing for a made-to-order flashing

Measuring the eaves before ordering gutter aprons

Measuring the eaves should show not only their length but also the space between the covering and the gutter. Gutter aprons must fit this cross-section and direct water in the intended direction. When ordering, it is worth separating straight sections, corners and ends. An accurate sketch makes quoting easier and reduces the number of reworks. It is also needed when we plan to use a popular catalogue profile. Before measuring, the type of covering and the method of fixing the gutter must be established. Its position relative to the end of the roof slope is important. The gutter apron should correspond to the arrangement that will actually be installed. A measurement taken before changing the gutter may become outdated.

By |2026-11-15T02:36:42+01:002022-01-02|Technology and applications|Comments Off on Measuring the eaves before ordering gutter aprons

What determines rafter size and spacing?

The rafter cross-section is not selected from a single table that applies to every house. You need the span, spacing, timber class, loads and support scheme. Deflection and connections also matter. Ready-made advice such as "a rafter of this size is enough under metal roofing sheet" leaves out far too much information. Below we explain what influences the selection and when the design needs to be reassessed. The design span does not have to be the total length of the rafter. It depends on where the rafter is supported. A rafter supported only at the eaves and the ridge behaves differently from one supported by an additional purlin. On top of that come the overhangs beyond the walls. The designer must know where the forces are transferred into the structure of the storey below.

By |2026-11-14T15:39:41+01:002022-01-02|Technology and applications|Comments Off on What determines rafter size and spacing?

Insulating an old roof with Utherm Sarking LE Plus boards

Replacing the roof covering creates an opportunity to install Utherm Sarking LE Plus without losing further centimetres of interior space. The renovation must, however, include an assessment of the layers that remain beneath it. Especially at the wall plate, it is worth taking advantage of the temporary access to the old connections. Utherm Sarking LE Plus is one of the PIR boards intended for pitched roofs. It has a multi-layer gas-tight laminate on both sides. The terms “polyurethane boards” and “polyurethane foam” are broader than the precise designation of the PIR product. The pre-renovation survey should cover the difference between Utherm Sarking LE and the LE Plus variant with an additional membrane. When surveying the existing assembly, the full name of the Sarking variant must be established before additional membranes are selected.

By |2026-11-16T00:11:51+01:002021-12-28|Technology and applications|Comments Off on Insulating an old roof with Utherm Sarking LE Plus boards

Buying PIR for renovation: measurements, opening-up inspections and fitting costs

In a renovation, the price of the board is only part of the expense. Repairs to the substrate, dismantling and fitting of flashings may be needed. PIR boards are worth ordering after measurements and after identifying the existing layers. This allows their small thickness to be used where it actually helps. PIR boards may look similar yet have different facings, strength and intended use. Before purchase, a current technical data sheet, declaration of performance and installation instructions are needed. A variant from an old project may not correspond to today's range. The order should specify the current product and the documents relating to its manufacture. An archived project may feature a product with a changed name or construction.

By |2026-11-16T00:09:57+01:002021-12-18|Technology and applications|Comments Off on Buying PIR for renovation: measurements, opening-up inspections and fitting costs

XPS on the foundation walls of a new house

Foundation wall insulation is easy to install while the excavation is open. A later correction requires renewed access to the underground part of the building. XPS should therefore be selected before work begins. Extruded polystyrene helps to limit heat losses and can shield the waterproofing against some mechanical damage. However, it does not replace the waterproofing itself. Both layers should form a planned system matched to the conditions of the plot. The foundation may be exposed to ground moisture, periodically backed-up water or water under pressure. These situations require different protective solutions. Before choosing XPS, the soil and water conditions and the design assumptions must be known. It is not enough to state that it was dry during excavation.

By |2026-11-16T04:52:07+01:002021-11-26|Technology and applications|Comments Off on XPS on the foundation walls of a new house

XPS on a terrace above a room. How does the inverted system work?

A terrace above a living room or garage is both a usable space and a roof. It must drain water, carry loads and limit heat loss. In the inverted system, XPS lies above the waterproofing. This order helps to shield the sealing layer from some of the external actions. Extruded polystyrene is considered because of its low water absorption and its mechanical properties. However, the success depends on the selection of all the terrace layers and its details. In the classic system, the waterproofing is above the thermal insulation. In the inverted solution, the order is different, and XPS shields the sealing layer from above. This can limit its exposure to solar radiation and to some temperature changes.

By |2026-11-16T04:50:41+01:002021-11-01|Technology and applications|Comments Off on XPS on a terrace above a room. How does the inverted system work?

SOPREMA EFIGREEN ITE for renovating façades and window reveals

The new ETICS layer is to adjoin the retained windows and doors and the old section of the façade. After removing the cladding, the width of the reveal and the condition of the substrate for the fixings must be checked. Additional insulation will not repair the damaged load-bearing part. The scope of the repair and the connection between the old and new layers should be established before the boards are installed. In a renovation, the scope described as external thermal insulation of a wall with façade cladding requires an investigation of the old layers. The first difficult place to inspect is the external window reveal and the adjacent façade bracket. It is not worth determining the thickness of EFIGREEN ITE solely on the basis of an old drawing. The measurement should cover the width of the reveal and the route of the fixings through the thermal insulation layer, taking into account changes made during earlier works.

By |2026-11-16T00:11:05+01:002021-10-25|Technology and applications|Comments Off on SOPREMA EFIGREEN ITE for renovating façades and window reveals

IDELCO α-therm ROOF for renovating a roof with a low parapet

Renovating a roof first requires establishing which layers of the old build-up remain and what condition they are in. IDELCO α-therm ROOF is a rigid PIR board for flat roofs, faced on both sides with a gas-tight laminate of kraft paper and aluminium layers. Before refurbishment, the layer build-up, its moisture content and its suitability as a substrate must be identified, and measurements must be taken at the outlets. On this basis the board thickness is selected, the change to the flashings is planned and the fixing of α-therm ROOF is determined from among the solutions permitted in the system. The terms “polyurethane boards” and “polyurethane foam” are broader than the PIR product designation.

By |2026-11-16T04:46:35+01:002021-10-08|Technology and applications|Comments Off on IDELCO α-therm ROOF for renovating a roof with a low parapet
Back to top